Manuals / TRENDnet / Computer Equipment / Network Card

TRENDnet TEW-603PI manual WPA/WPA2, WPA-PSK/WPA2-PSK, Use DHCP, Use static IP below

Models: TEW-603PI

1 44

Download 44 pages 55 Kb

Page 15

WPA/WPA2

WPA/WPA2

WPA encrypts all traffic between the access point and the client using either TKIP or AES encryption. Depending on the authentication protocol selected, each client must authenticate using their own unique username, password, and security certificate.

WPA-PSK/WPA2-PSK

WPA-PSK is a compromise between WPA and WEP. Like WEP, it uses a pre-shared key that every user of the network must have in order to send and receive data. Like WPA, it uses either TKIP or AES.

IMPORTANT

IT IS RECOMMEDED THAT YOU USE WPA OR WPA-PSKWHENEVER POSSIBLE. WPA (WI-FI PROTECTED ACCESS) PROVIDES STRONGER ENCRYPTION THAN THE EARLIER WEP (WIRED EQUIVALENT PRIVACY) METHOD.

5. Make the changes you want and click TCP/IP Config.

Select the Use IP Changer checkbox. This allows you to bypass your existing wireless TCP/ IP settings and configure TCP/IP settings for each profile.

Use DHCP

DHCP (Dynamic Host Configuration Protocol) automatically assign IP addresses. Check this radio button if your router is set to DHCP.

Use static IP below

Check this radio button if you have to enter a static IP address.

15

Image 15

TRENDnet TEW-603PI manual WPA/WPA2, WPA-PSK/WPA2-PSK, Use DHCP, Use static IP below

Contents

Page IMPORTANT NOTE FCC Radiation Exposure Statement Federal Communication Commission Interference StatementCE Mark Warning Configuring Wireless Security Table of ContentsHardware and Wireless Utility Exploring the Wireless Client Utility ScreensGetting Started with the TEW-603PI System Requirement Hardware and Wireless UtilityAbout Your Wireless MIMO PCI Adapter Package ContentProduct Outline Wireless MIMO PCI AdapterSide view of the PCI Adapter from bracket Overview of the Wireless Client Utility The Network Screen The Profile Screen The SiteSurvey ScreenThe Options Screen The Version Screen 1. Click Profile Working with Profiles3. Type a descriptive name for the profile such as Home or CoffeShop 7. Click Next. The WLAN Security Configuration screen appears 9. Click Next 1. Open the Wireless Client Utility and click Profile 2. Select the profile you want to modify and click PropertiesMODIFYING PROFILES WEP Wired Equivalent Privacy Use static IP below WPA/WPA2WPA-PSK/WPA2-PSK Use DHCPChecking for Available Access Points 1. Open the Wireless Client Utility and click Options Disabling the Wireless Client UtilityPage The Options Screen The Version Screen Exploring the Wireless Client Utility ScreensThe Network Screen The Network Screen The Profile Screen The SiteSurvey ScreenSecurity ” Shows the current network IP address The Profile Screen The SiteSurvey Screen DETAILED INFO. SCREEN The Options Screen The Version Screen Configuring Security Configuring Wireless Security2. Click the drop-down arrow at Security Mode and choose WEP 1. In the Properties window, click WLAN Security3. Click the Use Static WEP checkbox Select the encryption to match your access point CONFIGURING WPA & WPA2 Refer to the following to configure WPA / WPA21. Click the drop-down arrow at Security Mode and choose WPA / WPA2 CONFIGURING WPA-PSK & WPA2-PSK 4. Type in a unique User ID and Password under User Information Check this box if your network requires user certification and CONFIGURING 802.1X - EAP-TLS Glossary USER AUTHENTICATION SSIDTEMPORAL KEY INTEGRITY PROTOCOL TKIP Maintenance See “Maintenance” See “Troubleshooting”Appendix 3. Click Next in the Choose Destination Location screen Adapter - UninstallCORRECTIVE ACTION TroubleshootingPROBLEM PROBLEMThe TEW-603PI Problems Communicating With Other ComputersPROBLEM CORRECTIVE ACTIONAd-Hoc IBSS Verify that the peer computers is turned on Limited Warranty OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD