Manuals / Ultimate Products / Household Appliance / Garage Door Opener

Ultimate Products UP-206 manual Part 2 INSTALLING CHAIN DRIVE, Step, See Figure A

Models: UP-206

1 46

Download 46 pages 612 b

Page 14

Part 2:INSTALLING CHAIN DRIVE

12

Part 2:INSTALLING CHAIN DRIVE

STEP 1

NOTE: Before beginning installation make sure you have chain roller set-up (Part No. AP1325).

Determine which side of the door you are installing the air operator on; you will need at least 6” of shaft beyond track bracket for installing air-powered operator with chain.

See Figure A.

STEP 2

Position the chain sprocket assembly ( part # spk 1000 ) onto shaft against bearing as shown in figure B. Do not tighten set screws until you have hung operator around sprocket.

Image 14

Ultimate Products UP-206 manual Part 2 INSTALLING CHAIN DRIVE, Step, See Figure A

Contents

UP 2/086-00434/05  Supplies needed but not included with this kit Air-PoweredDoor Operator Installation GuideNecessary tools Step Part 1 BELT INSTALLATIONClearance Requirements tensioner kit must be installed.Part No Installing Tensioner KitBefore installing the air cylinder, the Step 2 Installing Sprocket KitInstalling Tensioner Kit Step Installing Speed Control KitAs shown on Page operator NOTE Remove clamp assembly CL-102from belt before installing belt onto Step 4 Attaching Belt to OperatorHanging Operator Completed Tensioner Kit will be as shown 1/4 And tighten both item ‘A’ and Item ‘C’ Completed Operator set up view Installation Of Chain Drive STEP Part 2 INSTALLING CHAIN DRIVESTEP See Figure AStep Installing Chain Chain RollerSpeed Control Kit StepSprocket Assembly Part No. SPK1000 StepAttach operator to vertical track after it is aligned with sprocket and operator hangs straight down using self- taping screws. See Figure K. Tighten chain with turnbuckle. After chain is tight, lock turnbuckle into place with ½” nut on threaded rod. See Figure L. Slide one enclosed clamp assembly Part No. AP1055 so that ¾” of the rod extends above the clamp assembly as shown in Figure M. Tighten all bolts StepNow attach Part No. ‘CL102’ to the Part Install the control AInstalling Air Lines PartDoor speed adjustments and fine tuning Part 6a U SeriesTesting Operator and Control Box A. Door slows down too soon when openingDoor speed adjustments and fine tuning Part 6b S SeriesDoor speed adjustments and fine tuning continued B. Door slows too soon when closingPart 6b S Series Door adjustments and fine tuning continuedC. Door Slows too Soon When Closing Note Only for S series operatorsTroubleshooting PartInstall Signal Senders Fixing Door or Operator ProblemsFixing Control Problems Part Automatic Oiler AdjustmentCable jumping solutions Partclosed for national holidays Model DC Model DC Model DC Description Typical Control Box Set-UpHome of the Best Buy Guarantee Photo Amplifier Wiring Directions Connections for Relay Output= + ZVE1 --Photo Amplifier SocketBlack wire goes Limit Switch Wiring and MountingLead side of limit switch & bracket Black wire goes to 3 on electric eyeWires to box Wall Suggested Installation of Magnetic LoopWiring Diagram for Magnetic Loop 24VacWiring Diagram Finder Timer to Control Box DISCONNECT POWER BEFORE PROCEEDINGOperator with Belt Operator with Chain 3.“o” ring - AP1004 4.check ball Power Supply Architectural Guide for Air-PowerOperator SystemControl Box DimensionsDimensions OperatorsOperator Placement Air UsageOperators with chains Superior or Economy Air-PoweredOperatorsUltimate Air-PoweredOperator Operators with beltsOperators without Oiler Cylinder OilingOperators with Automatic Oilers Tools and materials needed Seal Kit Procedures for Air-PoweredOperatorsItems included in the kit U-cupSealsNeedle Valve Piston Rod SealsBreather Vents and Check Ball closed for national holidaysPage Ultimate Products is closed for national holidays