Manuals / Ultimate Products / Household Appliance / Garage Door Opener

Ultimate Products UP-206 Installing Tensioner Kit, Before installing the air cylinder, the, OT101

Models: UP-206

1 46

Download 46 pages 612 b

Page 4

Step 2 Installing Sprocket Kit

2

Step 2 Installing Sprocket Kit

Position the 1½” spacer (Part No. SP101) onto the shaft against the bearing as shown.

Next slide the sprocket (Part No. BSP01) against the spacer.

Insert key (Part No. K101) of sprocket kit into the keyway of sprocket and tighten the set screws.

Set Screws

Installing Tensioner Kit
Before installing the air cylinder, the	Tension
tensioner kit must be installed.(Part No.	Rod
tensioner kit must be installed.(Part No.
OT101).

Washers (4)	Cotter
	Pins

Tensioner Roller

Image 4

Ultimate Products UP-206 Installing Tensioner Kit, Before installing the air cylinder, the, OT101, Installing Sprocket Kit

Contents

 UP 2/086-00434/05 Necessary tools Air-PoweredDoor Operator Installation GuideSupplies needed but not included with this kit Clearance Requirements Part 1 BELT INSTALLATIONStep Installing Tensioner Kit Before installing the air cylinder, thetensioner kit must be installed.Part No Step 2 Installing Sprocket KitInstalling Tensioner Kit As shown on Page Installing Speed Control KitStep NOTE Remove clamp assembly CL-102 from belt before installing belt ontooperator Step 4 Attaching Belt to OperatorHanging Operator Completed Tensioner Kit will be as shown 1/4 And tighten both item ‘A’ and Item ‘C’ Completed Operator set up view Installation Of Chain Drive Part 2 INSTALLING CHAIN DRIVE STEPSTEP See Figure AStep Installing Chain Chain RollerSpeed Control Kit StepSprocket Assembly Part No. SPK1000 StepAttach operator to vertical track after it is aligned with sprocket and operator hangs straight down using self- taping screws. See Figure K. Tighten chain with turnbuckle. After chain is tight, lock turnbuckle into place with ½” nut on threaded rod. See Figure L. Slide one enclosed clamp assembly Part No. AP1055 so that ¾” of the rod extends above the clamp assembly as shown in Figure M. Tighten all bolts StepNow attach Part No. ‘CL102’ to the Part Install the control AInstalling Air Lines PartPart 6a U Series Testing Operator and Control BoxDoor speed adjustments and fine tuning A. Door slows down too soon when openingPart 6b S Series Door speed adjustments and fine tuning continuedDoor speed adjustments and fine tuning B. Door slows too soon when closingDoor adjustments and fine tuning continued C. Door Slows too Soon When ClosingPart 6b S Series Note Only for S series operatorsPart Install Signal SendersTroubleshooting Fixing Door or Operator ProblemsFixing Control Problems Automatic Oiler Adjustment Cable jumping solutionsPart Partclosed for national holidays Model DC Model DC Model DC Home of the Best Buy Guarantee Typical Control Box Set-UpDescription Connections for Relay Output = +Photo Amplifier Wiring Directions ZVE1 --Photo Amplifier SocketLimit Switch Wiring and Mounting Lead side of limit switch & bracketBlack wire goes Black wire goes to 3 on electric eyeSuggested Installation of Magnetic Loop Wiring Diagram for Magnetic LoopWires to box Wall 24VacWiring Diagram Finder Timer to Control Box DISCONNECT POWER BEFORE PROCEEDINGOperator with Belt Operator with Chain 3.“o” ring - AP1004 4.check ball Architectural Guide for Air-PowerOperator System Control BoxPower Supply DimensionsOperators Operator PlacementDimensions Air UsageSuperior or Economy Air-PoweredOperators Ultimate Air-PoweredOperatorOperators with chains Operators with beltsOperators with Automatic Oilers Cylinder OilingOperators without Oiler Seal Kit Procedures for Air-PoweredOperators Items included in the kitTools and materials needed U-cupSealsPiston Rod Seals Breather Vents and Check BallNeedle Valve closed for national holidaysPage Ultimate Products is closed for national holidays