Manuals / Ultimate Products / Household Appliance / Garage Door Opener

Ultimate Products UP-206 manual Hanging Operator

Models: UP-206

1 46

Download 46 pages 612 b

Page 8

Hanging Operator

6

Remove belt roller (Part No. OP01) from center of operator. (roller is attached when operator is shipped from factory)

Slide bottom of turnbuckle onto rod closest to the wall leaving ½” of rod above turnbuckle (Part No. CL100). Tighten bolts of turnbuckle down onto rod and reinstall Belt Roller on operator.

NOTE: Turnbuckle will always be installed on rod that is closest to the wall

Hanging Operator

Step 5

Note: Insure door is fully closed before hanging operator.

Hang operator from the belt by placing the belt around the sprocket and behind Tensioner Roller, as shown.

Image 8

Ultimate Products UP-206 manual Hanging Operator

Contents

UP 2/086-00434/05  Supplies needed but not included with this kit Air-PoweredDoor Operator Installation GuideNecessary tools Step Part 1 BELT INSTALLATIONClearance Requirements Installing Tensioner Kit Before installing the air cylinder, thetensioner kit must be installed.Part No Step 2 Installing Sprocket KitInstalling Tensioner Kit Step Installing Speed Control KitAs shown on Page NOTE Remove clamp assembly CL-102 from belt before installing belt ontooperator Step 4 Attaching Belt to OperatorHanging Operator Completed Tensioner Kit will be as shown 1/4 And tighten both item ‘A’ and Item ‘C’ Completed Operator set up view Installation Of Chain Drive Part 2 INSTALLING CHAIN DRIVE STEPSTEP See Figure AStep Installing Chain Chain RollerSpeed Control Kit StepSprocket Assembly Part No. SPK1000 StepAttach operator to vertical track after it is aligned with sprocket and operator hangs straight down using self- taping screws. See Figure K. Tighten chain with turnbuckle. After chain is tight, lock turnbuckle into place with ½” nut on threaded rod. See Figure L. Slide one enclosed clamp assembly Part No. AP1055 so that ¾” of the rod extends above the clamp assembly as shown in Figure M. Tighten all bolts StepNow attach Part No. ‘CL102’ to the Part Install the control AInstalling Air Lines PartPart 6a U Series Testing Operator and Control BoxDoor speed adjustments and fine tuning A. Door slows down too soon when openingPart 6b S Series Door speed adjustments and fine tuning continuedDoor speed adjustments and fine tuning B. Door slows too soon when closingDoor adjustments and fine tuning continued C. Door Slows too Soon When ClosingPart 6b S Series Note Only for S series operatorsPart Install Signal SendersTroubleshooting Fixing Door or Operator ProblemsFixing Control Problems Automatic Oiler Adjustment Cable jumping solutionsPart Partclosed for national holidays Model DC Model DC Model DC Description Typical Control Box Set-UpHome of the Best Buy Guarantee Connections for Relay Output = +Photo Amplifier Wiring Directions ZVE1 --Photo Amplifier SocketLimit Switch Wiring and Mounting Lead side of limit switch & bracketBlack wire goes Black wire goes to 3 on electric eyeSuggested Installation of Magnetic Loop Wiring Diagram for Magnetic LoopWires to box Wall 24VacWiring Diagram Finder Timer to Control Box DISCONNECT POWER BEFORE PROCEEDINGOperator with Belt Operator with Chain 3.“o” ring - AP1004 4.check ball Architectural Guide for Air-PowerOperator System Control BoxPower Supply DimensionsOperators Operator PlacementDimensions Air UsageSuperior or Economy Air-PoweredOperators Ultimate Air-PoweredOperatorOperators with chains Operators with beltsOperators without Oiler Cylinder OilingOperators with Automatic Oilers Seal Kit Procedures for Air-PoweredOperators Items included in the kitTools and materials needed U-cupSealsPiston Rod Seals Breather Vents and Check BallNeedle Valve closed for national holidaysPage Ultimate Products is closed for national holidays