Manuals / Ultimate Products / Household Appliance / Garage Door Opener

Ultimate Products UP-206 manual Limit Switch Wiring and Mounting, Top of door, Track, 1/2”, Step

Models: UP-206

1 46

Download 46 pages 612 b

Page 34

Limit Switch Wiring and Mounting

Limit Switch Wiring and Mounting

Track

Top of door

Step 2:

Lead side of limit switch & bracket

1/2”

Magnet & L-bracket

Step 3:

Black wire goes to 3 on electric eye

Black wire goes

amplifier.

to 4 on electric eye amplifier.

Red wire goes to open on control box terminal strip.

Step 1:

Remove existing wire on amplifier between terminal 3 and open

Image 34

Ultimate Products UP-206 Limit Switch Wiring and Mounting, Top of door, Track, Lead side of limit switch & bracket, 1/2”

Contents

 UP 2/086-00434/05 Necessary tools Air-PoweredDoor Operator Installation GuideSupplies needed but not included with this kit Clearance Requirements Part 1 BELT INSTALLATIONStep tensioner kit must be installed.Part No Installing Tensioner KitBefore installing the air cylinder, the Step 2 Installing Sprocket KitInstalling Tensioner Kit As shown on Page Installing Speed Control KitStep operator NOTE Remove clamp assembly CL-102from belt before installing belt onto Step 4 Attaching Belt to OperatorHanging Operator Completed Tensioner Kit will be as shown 1/4 And tighten both item ‘A’ and Item ‘C’ Completed Operator set up view Installation Of Chain Drive STEP Part 2 INSTALLING CHAIN DRIVESTEP See Figure AStep Installing Chain Chain RollerSpeed Control Kit StepSprocket Assembly Part No. SPK1000 StepAttach operator to vertical track after it is aligned with sprocket and operator hangs straight down using self- taping screws. See Figure K. Tighten chain with turnbuckle. After chain is tight, lock turnbuckle into place with ½” nut on threaded rod. See Figure L. Slide one enclosed clamp assembly Part No. AP1055 so that ¾” of the rod extends above the clamp assembly as shown in Figure M. Tighten all bolts StepNow attach Part No. ‘CL102’ to the Part Install the control AInstalling Air Lines PartDoor speed adjustments and fine tuning Part 6a U SeriesTesting Operator and Control Box A. Door slows down too soon when openingDoor speed adjustments and fine tuning Part 6b S SeriesDoor speed adjustments and fine tuning continued B. Door slows too soon when closingPart 6b S Series Door adjustments and fine tuning continuedC. Door Slows too Soon When Closing Note Only for S series operatorsTroubleshooting PartInstall Signal Senders Fixing Door or Operator ProblemsFixing Control Problems Part Automatic Oiler AdjustmentCable jumping solutions Partclosed for national holidays Model DC Model DC Model DC Home of the Best Buy Guarantee Typical Control Box Set-UpDescription Photo Amplifier Wiring Directions Connections for Relay Output= + ZVE1 --Photo Amplifier SocketBlack wire goes Limit Switch Wiring and MountingLead side of limit switch & bracket Black wire goes to 3 on electric eyeWires to box Wall Suggested Installation of Magnetic LoopWiring Diagram for Magnetic Loop 24VacWiring Diagram Finder Timer to Control Box DISCONNECT POWER BEFORE PROCEEDINGOperator with Belt Operator with Chain 3.“o” ring - AP1004 4.check ball Power Supply Architectural Guide for Air-PowerOperator SystemControl Box DimensionsDimensions OperatorsOperator Placement Air UsageOperators with chains Superior or Economy Air-PoweredOperatorsUltimate Air-PoweredOperator Operators with beltsOperators with Automatic Oilers Cylinder OilingOperators without Oiler Tools and materials needed Seal Kit Procedures for Air-PoweredOperatorsItems included in the kit U-cupSealsNeedle Valve Piston Rod SealsBreather Vents and Check Ball closed for national holidaysPage Ultimate Products is closed for national holidays