WARNING

DO NOT ATTEMPT TO LIGHT THE PILOT BURNER WITH A FLAME.

4.Ignite the pilot. The micrometer should read 3 microamps minimum.

•If current reading is correct, replace the igniter module (see 10.13).

•If current reading is below 3 microamps, continually check the Flame Rectification Circuit (large orange wire, spark electrode, pilot burner hood, and ground connections). If necessary, tighten ground connections and/or replace defective component(s).

5.Check for moisture around the pilot burner, and for corrosion on the electrode and the pilot burner hood. If necessary, remove moisture with a dry, clean cloth. If hood and/or electrode are excessively corroded, replace pilot burner assembly.

10.16Steam Generator Gas Jet Manifolds P/N 123704 and 123705

1.Shut-off power and gas to the steamer.

2.Remove the right side panel.

3.Turn manual gas valve to the closed position.

4.Remove the four aluminum tubes connected to the manifolds. Disconnect using an open ended wrench.

5.Disconnect all wire connections to the pilot.

6.Remove the two screws from the pilot mounting bracket. Remove pilot from the gas manifold.

7.Using a wrench, remove the two top and one bottom bolts which hold the manifold to the steam generator manifold mounting bracket.

8.Remove the screws in the heat shield.

9.Remove the burner manifold from the appliance.

10.Remove the flame retention springs and injectors as required.

To Reassemble:

11.Replace the injectors and retention springs. Ensure a suitable gas sealant is used on the threads of the injectors to ensure a gas tight seal

12.Fit the burner manifold to the steam generator manifold mounting bracket.

13.Reinstall and tighten the aluminum tubes to the burner manifold.

NOTE: Ensure all gas connections are sound before continuing.

10.17 Timer Assembly

Timer Fastener Nut

P/N 100983

P/N 101145

1.Remove the three hex nuts which retain the control panel cover. Remove the cover.

2.Remove the knob from the timer. Under the knob is a hexagonal nut which holds the time mechanism to the steamer. Note that there is a flat on the timer shaft which corresponds to a frictional mounting hole on the knob.

3.From the left side, unplug the five terminals/wires (violet, gray, black, tan and white) from the timer mechanism and unplug the two black timer motor leads.

4.With an open-ended wrench, remove the hex nut holding the timer in place. The timer may then be removed from inside the compartment.

NOTE: Right below the timer shaft, the timer has a small plastic disk molded onto the case. There is a corresponding hole punched into the front panel. This hole may be seen from the inside of the compartment only when the timer is removed.

To Install:

5.Fit the timer in place making sure that it is properly placed so that the disk on the timer fits into the punched hole in the front panel.

6.Once the timer is properly located, tighten the hex nut so that the timer does not slip or rotate. Do not over-tighten the nut.

7.Align the flat of the knob hole with the flat on the timer shaft. Press the knob firmly onto the timer shaft.

8.Plug in the wires identified above and connect the two black wires from the motor leads.

9.Reattach the control panel cover.

28 OM/SM-HY-6G(CE)

Page 27 Page 29
Page 28
Image 28
Unified Brands HY-6G(CE) Steam Generator Gas Jet Manifolds P/N 123704, To Reassemble, Timer Assembly Timer Fastener Nut
Page 27 Page 29

HY-6G(CE) specifications

Unified Brands HY-6G(CE) is a pioneering cooking solution in the commercial kitchen landscape, known for its exceptional performance, versatility, and cutting-edge technologies. Designed to meet the rigorous demands of foodservice establishments, the HY-6G(CE) excels at efficiently preparing a wide range of dishes while ensuring consistent quality and safety.

One of the standout features of the HY-6G(CE) is its powerful heating capability. Equipped with advanced infrared heating technology, this unit delivers rapid and uniform heat distribution, making it ideal for both quick service and high-volume operations. The adjustable temperature controls allow chefs to fine-tune the cooking process, ensuring that every dish meets their exacting standards.

Another innovative aspect of the HY-6G(CE) is its energy efficiency. The incorporation of smart energy management systems ensures optimal power usage, reducing operational costs without sacrificing performance. The unit’s environmentally friendly design also aligns with sustainability initiatives, making it a responsible choice for modern kitchens.

The HY-6G(CE) boasts a user-friendly interface that facilitates ease of operation. Its digital display provides real-time feedback on cooking parameters, while programmable settings enable chefs to recall precise cooking profiles for various menu items. This feature not only streamlines kitchen workflow but also enhances productivity, allowing staff to focus on delivering exceptional customer service.

Durability is another hallmark of the HY-6G(CE). Constructed from high-quality stainless steel, it withstands the rigors of daily use in busy kitchens while resisting corrosion and wear. Its compact design allows for easy integration into existing kitchen layouts, making it an excellent option for both new builds and remodels.

Safety is paramount in any culinary environment, and the HY-6G(CE) addresses this with multiple safety features. These include automatic shut-off mechanisms and thermal protection systems that safeguard against overheating, ensuring secure operation even in the most demanding settings.

In summary, Unified Brands HY-6G(CE) stands out in the commercial cooking equipment market due to its blend of power, efficiency, and safety. With features that cater to the diverse needs of any foodservice establishment, it is an invaluable tool for chefs looking to elevate their culinary offerings while maintaining operational excellence. Whether in a bustling restaurant or a catering operation, the HY-6G(CE) is designed to deliver reliable and outstanding results.
Top Page Image Contents