Vanguard Heating VDVF36STP, VDVF36PN VDVF36P and VDVF36ST Series, Direct-Ventgas Fireplace Heater

® VDVF36P and VDVF36ST Series

DIRECT-VENT GAS FIREPLACE HEATER

INSTALLATION

WALL SWITCH

INSTALLATION

Since the VDVF36 series models use a valve that operates on millivolt current gen- erated by the pilot, a wall switch may be used to activate the gas control valve with- out the use of normal household electricity.

1.To remove the louvers, simultaneously pull both top end spring latches towards the center of the appliance until they are disengaged from locating holes. Repeat for bottom end spring latches and pull outward. Reverse the proce- dure to install louvers back onto the appliance (see Figure 32).

2.Connect the 18 ga. wires from wall switch to the gas control valve and microswitch, as shown in Figure 33.

WARNING: Do not wire re- mote wall switch to main power supply (Standard 120v household current).

ELECTRICAL HOOKUP FOR BLOWER ACCESSORY

Before blower accessory can be operated, it must be properly connected to a standard 120 VAC power source. Refer to Wiring Diagram on page 23.

An outlet box with two receptacles has been supplied for your convenience, located on the lower left side of the appliance (see Figure 34). An optional remote control may be installed at any time.

CAUTION: Due to high tem- peratures, make sure no wires are touching the bottom of the firebox.

For Optional

Fan Kit

From Blower

Assembly

OPTIONAL WIRELESS HAND- HELD REMOTE CONTROL (GHRC(T) SERIES) INSTALLATION

Note: If using an optional wireless hand- held remote control, the wall switch is no longer operational.

NOTICE: Only use alkaline bat- teries (not included).

Installing Receiver

1.	Remove access panel from lower front
	face of firebox. Lift straight up on ac-
	cess panel until it stops. Pull bottom of
	access panel forward, then down.
2.	Disconnect wall switch wires from TH
	and TPTH terminals on control valve
	(see Figure 33).
3.	Install remote receiver unit onto mount-
	ing bracket using the two plastic mount-
	ing clips (see Figure 35).
4.	Connect wires to control valve. Con-
	nect white wire to terminal TH. Con-
	nect red wire to terminal TPTH.
5.	Locate the battery clip mounted on the
	back of the receiver (see Figure 36).
6.	Slide 9-volt battery (not included)

Glass	Locating	Figure 34 - Connecting Blower Accessory
	Holes	to Power Supply

Wall Switch

Spring(Supplied)

Latch

Figure 32 - Removing Louver

To

Thermopile

			O
			IL	T
			P
	N		16AI
	O
O	T				TH
L				7
I
P		L	I
	FFO	O
			H

	through the clip.
7.	Attach the terminal wires to the battery
	(see Figure 36).
8.	Replace access panel. Place top of ac-
	cess panel into opening and slide up.
	Push bottom of access panel in and
	slide down to install.

Plastic

ReceiverMounting

Clips

Mounting

Bracket

Figure 35 - Installing Remote Receiver (Shown from Rear of Mounting Bracket)

9-Volt Battery

	TP
E	TPTH
	A

Route Millivolt Wires (Supplied)	(Back View)
Through Gas Line Conduit Sleeve

Figure 33 - Wall Switch Wiring Diagram

Battery Clip

Terminal Wires

Receiver

Note: If any of the original wire supplied must be replaced, use type 18 AWG-105 degree C (25 feet length MAXIMUM) or equivalent.

Figure 36 - Installing Battery in Receiver

16 105706