OWNER’S MANUAL
PRE-INSTALLATION PREPARATION
GENERAL VENTING
Note: Terminations are not designed for
Continued
13"
29"
10 1/4"
8 3/4"
9 1/4" | 41" |
37"
41"
371/2"
411/2"
58"
installation prior to transportation.
These models are approved for use with Simpson
Your fireplace is approved to be vented either through the side wall, or vertically using the following guidelines:
• | Only use Vanguard or Simpson Dura- |
| Vent GS venting components or kits spe- |
| cifically approved for this fireplace. |
• Minimum clearance between vent pipes | |
| and combustible materials is 1" (25 mm), |
| except where stated otherwise. |
Nailing Tabs • | Combustible material may be flush with |
| the top front of fireplace with a maxi- |
| mum thickness of 3/4". |
• Do not recess venting terminals into a | |
Note: Where two numbers are given the top number is exclusive to the 37" Fireplace and the bottom number is exclusive to the 41" Fireplace
Figure 6 - Framing Clearances for Corner Installation
|
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
| 2 |
|
|
Note: There must be a |
|
|
|
|
|
| 3 |
|
| ||||
A |
|
|
|
| Wall | ||||||||
minimum clearance of |
|
|
|
|
|
| 4 |
| |||||
|
|
|
|
|
|
|
| ||||||
18" above top of louver |
|
|
|
|
|
|
|
|
| ||||
opening when installing a |
| B |
|
| 5 |
|
| ||||||
television or entertain- |
|
|
|
| C |
|
|
| |||||
ment center above the |
|
|
|
| 6 |
|
| ||||||
|
|
|
|
|
|
|
| ||||||
fireplace. |
|
|
|
|
|
|
| D |
|
|
| ||
|
|
|
|
|
|
|
|
|
| E | 7 |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| F | G |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Top of Louver Opening | |||
|
|
|
|
|
|
|
|
|
|
| |||
| Ref. |
| Mantel Depth |
| Ref. |
| Mantel from Top |
|
|
| |||
|
|
|
|
|
|
|
|
| of Louver Opening |
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| 1 |
| 14" (356mm) |
| A |
|
| 16" (406mm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
| 2 |
| 12" (305mm) |
| B |
|
| 14" (356mm) |
|
|
| ||
| 3 |
| 10" (254mm) |
| C |
|
| 12" (305mm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
| 4 |
| 8" (203mm) |
| D |
|
| 10" (254mm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
| 5 |
| 6" (152mm) |
| E |
|
| 8" (203mm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
| 6 |
| 4" (101mm) |
| F |
|
| 6" (152mm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
| 7 |
| 2" (51mm) |
| G |
|
| 4" (101mm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 7 - Clearances for Combustible Mantels
wall or siding. |
• Install horizontal venting with a 1/4" rise for |
every 12" of run toward the termination. |
• You may paint the vent terminal with |
450ºF (232ºC) |
ordinate with the exterior finish. |
• There must not be any obstruction such |
as bushes, garden sheds, fences, decks, |
or utility buildings within 24" from the |
front of the termination cap. |
• Do not locate termination cap where exces- |
sive snow or ice build up may occur. Be sure |
to clear vent termination area after snow falls |
to prevent accidental blockage of venting |
system. When using snow blowers, do not |
direct snow towards vent termination area. |
LOCATION OF VENT
TERMINATION
When locating vent termination, it is impor- tant to observe the minimum clearances shown in Figure 8, page 6. You will avoid extra framing by positioning your fireplace against an already existing framing mem- ber. The sides of the fireplace may be posi- tioned directly against combustible walls.
*Check with local codes or with the current CAN/CGA B149[.1 or .2] Installation Codes for Canada or the USA Installations follow the current National Fuel Gas Code, ANS Z223.1, also known as NFPA 54.
Continued
106497 | 5 |
