Vermont Castings, Majestic Products RHEDV Direct Vent Insert
| 1/2" Gas Supply |
| 1/2" x 3/8" Reducer |
| 3/8" x 3/8" Shut Off Valve |
| 3/8" Union |
| 3/8" Nipple |
FP1278 | |
Fig. 1 | Typical gas supply installation. |
Always check for gas leaks with a mild soap and water solution. Do not use an open flame for leak testing.
|
|
| Manifold Gas |
|
|
| Outlet |
Thermostat | Brass | Brass Plug | |
Plug |
| ||
Bulb |
|
| |
|
| Pressure | |
|
|
| |
|
| Gas Inlet | Regulator |
|
|
| |
Thermocouple Inlet |
| ||
Pilot Tube Entry |
| ||
|
|
| Control |
| Pilot Adjustment | Knob | |
| Control Knob | ||
| Screw | ||
|
| ||
|
|
| HI |
|
| it | OFF |
|
| LO | PILOT |
|
| Minimum Rate Screw | |
|
| (Nonadjustable) | HV118 |
Fig. 2 On fireplaces equipped with the Eurosit 630 gas valve, there are brass plugs in two of the holes. These plugs are not to be removed. The gas inlet hole has a plastic cap in it.
Remove the plastic cap and connect your gas supply line at this point.
Fan Kit
115 volt, 60 Hz. 56W
The fan kit includes the following: fan, temperature sensor, speed control and a 6 ft. cord. The following explains how to start and set the fan for automatic operation.
1.Plug in the electrical cord.
2.Start gas fire - see lighting procedures.
3.Turn on fan speed control.
4.Wait until the unit has warmed up sufficiently to activate the termperature sensor, approx.
6
5.Once fan starts, adjust speed control to desired fan speed. The fan will now automatically come on every time the fireplace is in operation. Should the fan not be needed simply turn off the speed control.
The appliance, when installed must be electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code.
U.S. Installations, follow local codes and the National Electrical Code, ANSI/NFPA No. 70.
Should this fan require servicing, the power supply must be disconnected. For rewiring of any replacement components refer to Figure 4.
Fan Removal Instructions
1.Turn off gas and electricity.
2.Remove the front glass.
3.Remove the logs.
CAUTION: Logs may be hot!
4.Remove burner assembly and rear log support plate.
5.Remove the fan mounting nuts (2 nuts). (Fig. 3)
6.Slip off the electrical connector at the motor.
7.Lift out the fan.
8.To reinstall reverse procedure.
Screw
Stud
Thermal Sensor is | Fan is Installed at | ||||||||||||
Attached to Burner | |||||||||||||
the Back of the | |||||||||||||
Base | |||||||||||||
Air Intake Box | |||||||||||||
|
|
|
|
|
|
| |||||||
|
|
|
| Screw Stud |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
Fan Speed Control/Junction Box
| FP1252 |
Fig. 3 | Fan location. |
| Fan |
| Temperature Sensor |
Speed | |
Control | |
Black |
|
White |
|
Ground | |
| FP394 |
Fig. 4 | Wiring diagram. |
| 10000801 |