SET MODE

 

 

 

 

 

 

 

 

SET MODE ITEM

FUNCTION

 

AVAILABLE VALUES

 

(DEFALT: UNDERLINED BOLD)

55: MEMORY SKIP

Selects the Memory Scan channel-selection mode.

 

OFF / SKIP / ONLY

56: MEMORY WRITE

Determines the method of selecting channels for Memory Storage.

 

NEXT / LOWER

57: MESSAGE LIST

Programming a Member List for the Message feature.

--

58: MESSAGE REGISTER

Selects your Personal ID for the Message feature.

--

59: MESSAGE SELECT

Programming a Message for the Message feature.

--

60: MIC GAIN

Adjusts the microphone gain level.

 

LEVEL 1 ~ LEVEL 9 (LEVEL 5)

61: MONI/T-CALL

Selects the MONI key (just below the PTT switch) function.

 

MONI / T-CALLÚ1

62: MUTE

Adjusts the receiver audio output level when the MUTE function was activated.

 

MUTE 30%, MUTE 50%,

 

 

 

MUTE 100%, or OFF

63: OFF TIMER

Set the OFF Timer time.

--

64: ON TIMER

Set the ON Timer time.

--

65: OPENING MESSAGE

Selects the Opening Message that appears when the radio is powered on.

 

NORMAL / OFF / DC / MESSAGE

66: PAGER ANS-BACK

Enables/Disables the Answer Back function of the Enhanced CTCSS Paging & Code Squelch.

 

ON / OFF

67: PAGER CODE-RX

Sets the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch.

--

68: PAGER CODE-TX

Sets the Transmitting Pager Code for the Enhanced CTCSS Paging & Code Squelch.

--

69: PASSWORD

Programming and activating the Password feature.

--

70: PR FREQUENCY

Program the CTCSS Tone Frequency for the User Programmed Reverse CTCSS Decoder.

 

300Hz ~ 3000Hz (1000Hz/step) (1600Hz)

71: PRI REVERT

Enables/Disables the Priority Revert feature.

 

ON / OFF

72: PRI TIME

Selects the time between the Priority (Dual Watch) channel checks, when the feature is

 

0.1sec ~ 0.9sec (0.1sec/step) or

 

active.

 

1.0sec ~ 10.0sec (0.5sec/step) (5.0sec)

73: PTT DELAY

Selects the time delay before the carrier is transmitted, when the PTT switch is pressed.

 

OFF / 20ms / 50ms / 100ms / 200ms

74: RPT ARS

Enables/Disables the Automatic Repeater Shift function.

 

ON / OFF

75: RPT SHIFT

Sets the Repeater Shift Direction.

 

SIMPLEX / -RPT / +RPT

76: RPT SHIFT FREQ

Sets the magnitude of the Repeater Shift.

 

0.000MHz ~ 150.000MHz (50 kHz/step)Ú2

77: RX AF DUAL

Select the resume mode of the AF-Dual Operation.

 

TRX 1sec ~ TRX 10sec / HOLD /

 

 

 

TX 1sec ~ TX 10sec (TRX 2sec)

78: RX MODE

Sets the receiving mode.

 

AUTO / N-FM / AM / W-FM

79: SAVE RX

Selects the Receive-mode Battery Saver interval (“sleep” ratio).

 

0.2sec ~ 0.9sec (0.1sec/step) or

 

 

 

1.0sec ~ 10.0sec (0.5sec/step)

80: SAVE TX

Enables/Disables the Transmitter Battery Saver.

 

ON / OFF

81: SCAN LAMP

Enables/Disables the Scan Lamp (while scanner is paused).

 

ON / OFF

82: SCAN RE-START

Selects the Scan Re-start Delay time.

 

0.1sec ~ 0.9sec (0.1sec/step) or

 

 

 

1.0sec ~ 10.0sec (0.5sec/step) (2.0sec)

83: SCAN RESUME

Selects the Scan Resume mode.

 

2.0sec ~ 10.0sec (0.5sec/step) /BUSY /

 

 

 

HOLD (5.0sec)

84: SENSOR DISPLAY

Selects the sensor information when the transceiver is operating in the “Mono” band mode

 

DC / TEMP / WAVE / BARO / ALTI / OFF

 

with large characters.

 

 

85: SENSOR INFORMATION

Indicates the Information of the internal sensors.

--

86: SET MODE CSR

Selects the Set Mode Cursor.

 

Nine patterns

87: SET MODE FORMAT

Selects the display format of the Set Mode operation.

 

LIST / ITEM

88: SMART SEARCH

Selects the Smart Search Sweep mode.

 

SINGLE / CONTINUOUS

89: S-METER SYMBOL

Selects the S- & TX PO meter Symbol.

 

Four patterns

90: SPEAKER OUT

Enables/Disables the FM Broadcast audio output to the internal speaker when using the

 

AUTO / SPEAKER

 

earphone antenna.

 

 

91: SPEC-ANALYZER

Selects the Spectrum Analyzer sweep mode.

 

1Time / CONTINUOUS / Full Time

92: SQL LEVEL

Sets the Squelch threshold level.

 

LEVEL 0 ~ LEVEL 15 (LEVEL 1)

 

 

 

(AM and Narrow FM),

 

 

 

LEVEL 0 ~ LEVEL 8 (LEVEL 2)

 

 

 

(Wide FM and AM Broadcast)

93: SQL S-METER

Adjusts the Squelch threshold level to the S-meter level.

 

OFF / LEVEL 0 ~ LEVEL 9

94: SQL SPLIT

Enables/disables split CTCSS/DCS coding.

 

OFF / ON

95: SQL TYPE

Selects the Tone Encoder and/or Decoder mode.

 

OFF / TONE / TONE SQL / DCS /

 

 

 

REV TONE / PR FREQ / PAGER / MESSAGE

96: STEP FREQUENCY

Setting of the DIAL frequency steps.

 

AUTO / 5.0 / 6.25 / 8.33 / 9.0 / 10.0 / 12.5 /

 

 

 

15.0 / 20.0 / 25.0 / 50.0 / 100.0 kHz

97: STEREO

Enables/Disables the stereo output while receiving the FM Broadcast band.

 

STEREO / MONO

98: TIME SET

Sets the Clock time.

--

99: TONE FREQUENCY

Setting of the CTCSS Tone Frequency

 

50 standard CTCSS tones (100.0Hz)

100: TONE-SRCH MUTE

Enables/Disables the receiver audio output while the Tone Search Scanner is activated.

 

ON / OFF

101: TONE-SRCH SPEED

Selects the Tone Search Scanner speed.

 

FAST (2.5 tone/sec) / SLOW (1.25 tone/sec)

102: TOT

Setting of the TOT time

 

OFF / 0.5min ~ 10.0min (0.5min/step)

 

 

 

(3.0min)

103: UNIT OFFSET

Correcting the Sensor Unit.

--

104: UNIT SELECT

Select the measurement units of the Sensor Unit.

 

TEMP: °C / °FÚ1

 

 

 

BARO: HPA / mb / mmHg / inch

 

 

 

ALTITUDE: m / ft

105: VFO MODE

Selects or disables the VFO band edge limiting for the current band.

 

ALL / BAND

106: VFO SKIP

Setting My Band.

--

107: VOLUME MODE

Select the [VOL] key function.

 

NORMAL / AUTO BACK

108: VOX

Enables/Disables VOX operation; sets VOX sensitivity.

 

OFF / HIGH / LOW

109: VOX DELAY

Selects the VOX delay (“hang”) time.

 

0.5sec / 1.0sec / 1.5sec /

 

 

 

2.0sec / 2.5sec / 3.0sec

110: WAVE MONITOR

Selects the Wave-Form display while indicating the Wave-Form via Set Mode Item 84: SEN-

 

ALL / RX SIGNAL / TX MODULATION

 

SOR DISPLAY.

 

 

111: WX ALERT

Enables/Disables the Weather Alert Feature

 

ON / OFF

Ú1: Depends on the transceiver version.

Ú2: Depends on the operating band and transceiver version.

VX-8R OPERATING MANUAL

139