SET MODE

 

 

 

 

DTMF SETTING

SET

MODE ITEM

AVAILABLE VALUES (DEFAULT: BOLD ITALIC)

ˆ Selects the DTMF Autodialer Delay Time.

28:

DTMF DELAY

50ms / 250ms / 450ms / 750ms / 1000ms

ˆ Enables/Disables the DTMF Autodial feature.

29: DTMF MANUAL/AUTO

MANUAL / AUTO

ˆ Programming the DTMF Autodialer.

30: DTMF SELECT

--

ˆ Selects the DTMF Autodialer Sending Speed.

31: DTMF SPEED

50mS / 100mS

SWITCH/KNOB SETTING

SET

MODE ITEM

AVAILABLE VALUES (DEFAULT: BOLD ITALIC)

ˆ Set the duration that a secondary function of the [F/W] key (press and holding the [F/W] key) is held

36:

FW KEY HOLD TIME

0.3sec / 0.5sec / 0.7sec / 1.0sec / 1.5sec

determines the function they activate.

39: HOME/REVERSE

HOME / REV

ˆ Selects the function of the [H/M] key.

ˆ Selects the Control Locking lockout combination.

51: LOCK

KEY / DIAL / KEY&DIAL / PTT / KEY&PTT /

ˆ Selects the MONI key (just below the PTT switch) function.

61: MONI/T-CALL

DIAL&PTT / ALL

MONI / T-CALL

ˆ Selects the time delay before the carrier is transmitted, when the PTT switch is pressed.

73: PTT DELAY

OFF / 20ms / 50ms / 100ms / 200ms

ˆ Select the [VOL] key function.

107: VOLUME MODE

NORMAL / AUTO BACK

DISPLAY SETTING

SET

MODE ITEM

ˆ Indicates the DC Supply Voltage.

25: DC VOLTAGE

ˆ Selects the LCD/Keypad Lamp mode.

46: LAMP

ˆ Setting the Display contrast level.

48: LCD CONTRAST

ˆ Setting the Display brightness level.

49: LCD DIMMER

ˆ Illuminates the white LED light continuously (useful as emergency flashlight at night).

50: LED LIGHT

ˆ Selects the Opening Message that appears when the radio is powered on.

65: OPENING MESSAGE

ˆ Selects the sensor information when the transceiver is operating in the “Mono” band mode with large

84: SENSOR DISPLAY

character.

85: SENSOR INFORMATION

ˆ Displays internal sensor information.

ˆ Selects the S- & TX PO meter Symbol.

89: S-METER SYMBOL

ˆ Selects the Spectrum Analyzer sweep mode.

91: SPEC-ANALYZER

ˆ Calibrating the Sensor Unit.

103: UNIT OFFSET

ˆ Selects the measurement units of the Sensor Unit.

104: UNIT SELECT

ˆSelects the Wave-Form display while indicating the Wave-Form via Set Mode Item 84: SENSOR DISPLAY. 110: WAVE MONITOR

AVAILABLE VALUES (DEFAULT: BOLD ITALIC)

--

KEY 2sec - KEY 10sec / CONTINUOUS / OFF (KEY 5sec)

LEVEL 1 ~ LEVEL32 (LEVEL24) LEVEL 1 ~ LEVEL 4

--

NORMAL / OFF / DC / MESSAGE

DC / TEMP / WAVE / BARO / ALTI / WX / OFF

--

Four patterns

1Time / Continuous / Full Time BARO: -1000 ~ 0 ~ +1000, ALTITUDE: -1000 ~ 0 ~ +1000 TEMP: °C / °F,

BARO: HPA / mb / mmHg / inch,

ALTITUDE: m / ft

ALL / RX SIGNAL / TX MODULATION

BEEP SETTING

SET

MODE ITEM

AVAILABLE VALUES (DEFAULT: BOLD ITALIC)

ˆ Enables/Disables the Band-edge beeper while selecting the frequency with the DIAL knob.

10:

BEEP EDGE

ON / OFF

ˆ Adjust the Beep volume level.

11: BEEP LEVEL

LEVEL 1 - LEVEL 9 (LEVEL 5)

ˆ Create the Beep Melody for Bell ringer function.

12: BEEP MELODY

--

ˆ Enables/Disables the keypad beeper.

13: BEEP SELECT

KEY & SCAN / KEY / OFF

ˆ Select the CW tone pitch for the CW Learning, CW Training, and CW Identifier functions.

23: CW PITCH

400 - 1000 Hz (50 Hz/step) (700 Hz)

MISCELLANEOUS SETTING

SET

MODE ITEM

AVAILABLE VALUES (DEFAULT: BOLD ITALIC)

ˆ Select the antenna to be used for the AM Broadcast listening.

1: ANTENNA AM

BAR & EXT / BAR ANTENNA

ˆ Enables/Disables the receiver Front-end Attenuator.

2: ANTENNA ATT

ON / OFF

ˆ Select the antenna to be used for the FM Broadcast listening.

3: ANTENNA FM

EXT ANTENNA / EARPHONE

ˆ Enables/Disables the Busy Channel Lock-Out feature.

9: BCLO

ON / OFF

ˆ Selects the Channel Counter Search Width.

19: CH COUNTER

±5 MHz / ±10 MHz / ±50 MHz / ±100 MHz

ˆ Shifting of CPU clock frequency.

20: CLOCK SHIFT

ON / OFF

ˆ Enables/Disables the CW Learning feature.

22: CW LEARNING

--

ˆ Enables/Disables the CW Training feature.

24: CW TRAINING

--

ˆ Enables/Disables the extended Set Mode Menu.

35: EXTENDED MENU

ON / OFF

ˆ Reducing the Deviation level by 50 %.

37: HALF DEVIATION

ON / OFF

ˆ Enables/Disables the function of the VFO DIAL knob, while in the Home Channel mode.

38: HOME VFO

DISABLE / ENABLE

ˆ Selects the language for the Set Mode selections.

47: LANGUAGE

ENGLISH / JAPANESE

ˆ Adjusts the microphone gain level.

60: MIC GAIN

LEVEL 1 ~ LEVEL 9 (LEVEL 5)

ˆ Adjusts the receiver audio output level when the MUTE function was activated.

62: MUTE

MUTE 30%,MUTE 50%, MUTE 100%, or OFF

ˆ Set the OFF Timer time.

63: OFF TIMER

--

ˆ Set the ON Timer time.

64: ON TIMER

--

ˆ Programming and activating the Password feature.

69: PASSWORD

--

ˆ Select the resume mode of the AF-Dual Operation.

77: RX AF DUAL

TRX 1sec ~ TRX 10sec /

ˆ Sets the receiving mode.

78: RX MODE

HOLD / TX 1sec ~ TX 10sec (TRX 2sec)

AUTO / NFM / AM / WFM

ˆ Selects the Set Mode Cursor.

86: SET MODE CSR

Nine patterns

ˆ Selects the display format of the Set Mode operation.

87: SET MODE FORMAT

LIST / ITEM

ˆ Selects the Smart Search Sweep mode.

88: SMART SEARCH

SINGLE / CONTINUOUS

ˆ Enables/Disables the FM Broadcast audio output to the internal speaker when using the earphone antenna.

90: SPEAKER OUT

AUTO / SPEAKER

ˆ Sets the Squelch threshold level.

92: SQL LEVEL

LEVEL 0 ~ LEVEL 15 (LEVEL 1)

 

 

 

(AM and Narrow FM),

 

 

 

LEVEL 0 ~ LEVEL 8 (LEVEL 2)

 

93: SQL S-METER

(Wide FM and AM Broadcast)

ˆ Adjusts the Squelch threshold level to the S-meter level.

OFF / LEVEL 0 ~ LEVEL 9

96: STEP FREQUENCY

AUTO / 5.0 /6.25 / 8.33 / 9.0 / 10.0 / 12.5 / 15.0 /

ˆ Setting of the DIAL frequency steps.

97: STEREO

20.0 / 25.0 / 50.0 / 100 kHz

ˆ Enables/Disables the stereo output while receiving the FM Broadcast band.

STEREO / MONO

98: TIME SET

--

ˆ Sets the Clock time.

102: TOT

OFF / 0.5min ~ 10.0min (0.5min/step) (3.0min)

ˆ Setting of the TOT time

105: VFO MODE

ALL / BAND

ˆ Selects or disables the VFO band edge limiting for the current band.

106: VFO SKIP

--

ˆ Set My Band.

108: VOX

OFF / HIGH / LOW

ˆ Enables/Disables VOX operation; sets VOX sensitivity.

109: VOX DELAY

0.5sec / 1.0sec / 2.0sec

ˆ Selects the VOX delay (“hang”) time.

111: WX ALERT

ON / OFF

ˆ Enables/Disables the Weather Alert Feature

 

 

 

VX-8R OPERATING MANUAL

141