|
|
|
|
| S T E P 3 | PINK BAG |
|
|
|
|
| • Place the top left frame (AB4) on the left | |
|
|
|
|
| side uprights (AG1 & AG2), with the | |
|
|
|
|
| protruding bolt ends going through holes | |
|
|
|
|
| in the left rear upright (AG2). Slide a flat | |
|
|
|
|
| washer (10.2x22x2) and lock washer | |
|
|
|
|
| (10.2x18.4x2.5) over each bolt end, and | |
|
|
|
|
| secure with an acorn nut (M10). Secure | |
|
|
|
|
| two bolts (M10x100) with a lock washer | |
|
|
|
|
| (10.2x18.4x2.5) and a flat washer | |
|
|
|
|
| (10.2x22x2) through holes over the top of | |
|
| AB4 |
|
| front chrome upright (AG1). Repeat this | |
|
|
|
|
|
| |
|
|
| AB2 |
| process for top right frame (AB5). | |
|
| AB1 |
|
| • | Place the top rear frame (AB2) up |
| B21 |
|
| against the back of the top left and right | ||
|
|
|
| |||
|
|
|
|
|
| |
AB3 |
|
|
|
| frames (AB4 & AB5). Insert two bolts | |
|
|
|
|
|
| |
|
|
|
| AB5 | (M10x70) with flat washers (10.2x22x2) | |
|
|
|
|
| ||
|
|
|
|
| through the holes on both sides of top | |
|
|
|
|
| frames, and secure the connection with | |
|
|
|
|
| another flat washer on each bolt, and a | |
|
|
|
|
| nylon nut (M10). | |
|
|
|
|
| • Take the top center pulley support (AB1) | |
|
|
|
|
| with the pulley bracket side down, place | |
|
|
|
|
| the holes on the short end over the middle | |
|
|
|
|
| holes in top rear frame (AB2). Secure in | |
|
|
|
|
| place by sliding two bolts (M10x70) with | |
|
|
|
|
| flat washers (10.2x22x2) through the | |
|
|
|
|
| holes. Slide another flat washer onto each | |
|
|
|
|
| bolt and tighten with a nylon nut (M10). | |
|
|
|
|
| • Grab the top front frame (AB3) and | |
|
|
|
|
| align the holes in the center with the holes | |
|
|
|
|
| in top center pulley support (AB1). Slide | |
|
|
|
|
| two bolts (M10x70) with flat washers | |
|
|
|
|
| (10.2x22x2) through the holes, placing | |
|
|
|
|
| another flat washer onto the bolts and | |
|
|
|
|
| securing with a nylon nut (M10). To connect | |
|
|
|
|
| to both left and right top frames (AB4 & | |
|
|
|
|
| AB5), slide a bolt (M10x70) with a lock | |
|
|
|
|
| washer (10.2x18.4x2.5) and flat washer | |
|
|
|
|
| (10.2x22x2) through the front holes in the | |
|
|
|
|
| connection points (See diagram for | |
|
|
|
|
| clarification). For other hole, use a bolt | |
|
|
|
|
| (M10x70) with a flat washer (10.2x22x2) | |
|
|
|
|
| and connect other side of bolt using another | |
|
|
|
|
| flat washer and a nylon nut (M10). | |
|
|
|
|
| Tighten the two front center bolts. | |
|
|
|
|
| • Attach the top front frame cover (B21) to | |
|
|
|
|
| the | top front frame (AB3) using two |
|
|
|
|
| bolts (M8x20) and two flat washers | |
|
|
|
|
| (8.4x15.5x1.6). | |
11
