Manuals / Vulcan-Hart / Kitchen Appliance / Electric Steamer

Vulcan-Hart C24GA6, C24GA10, ML-136021, ML-136022 service manual Pilot/Spark Probe Flame Sensor

Models: C24GA6 ML-136021, C24GA10 ML-136022 C24GA6, C24GA10, ML-136021, ML-136022

1 39

Download 39 pages 44.4 Kb

Page 12

PILOT/SPARK PROBE

C24GA SERIES CONVECTION STEAMERS - REMOVALAND REPLACEMENT OF PARTS

4.Disconnect the water lines for the solenoid valve being serviced and remove the solenoid valve from the unit.

5.Reverse procedure to install solenoid valve.

PILOT/SPARK PROBE

FLAME SENSOR

1.Remove main burner assembly as outlined under MAIN BURNER in REMOVALAND REPLACEMENT OF PARTS.

2.Remove the pilot assembly by disconnecting gas tube to the pilot burner and remove screws holding pilot assembly.

3.Replace the malfunctioning flame sensor or pilot assembly.

4.Reverse procedure to install a new flame sensor or pilot assembly.

5.Check for proper operation.

F35425 (February 2006)		Page 12 of 40

Image 12

Vulcan-Hart C24GA6, C24GA10, ML-136021, ML-136022, C24GA6 ML-136021, C24GA10 ML-136022 Pilot/Spark Probe Flame Sensor

Contents

CONVECTION STEAMERSC24GA SERIES MODELSTABLE OF CONTENTS C24GA SERIES CONVECTION STEAMERS INSTALLATION CLEANINGSPECIFICATIONS GENERALREMOVAL AND REPLACEMENT OF PARTS COVERS AND PANELSCOOKING COMPARTMENT DOOR Door AssemblyCabinet Base Left Side Panel Cabinet Base Rear PanelDoor Gasket Door HandleCOMPARTMENT CONTROLS Door Latch AssemblyGENERATOR ASSEMBLY MAIN BURNERGAS COMBINATION CONTROL VALVE 4.Disconnect wires to burner assembly 2.Remove rear and side panels as outlined underCOVERS AND PANELS 12.Disconnect gas tubing from rear panelFILL AND COLD WATER SOLENOID VALVES PILOT/SPARK PROBE FLAME SENSOR SERVICE PROCEDURES AND ADJUSTMENTS BLOWER AIR PRESSURE ADJUSTMENTAIR PRESSURE SWITCH ADJUSTMENT PILOT BURNER ADJUSTMENT Operating Pressure Switch Thumb Wheel Adjustment Inlet Water/Steam StrainerAUTOMATIC IGNITION SYSTEMS Spark Ignition Control TestMANIFOLD PRESSURE ADJUSTMENT IGNITION TESTDOOR COOKING COMPARTMENTLatch Adjustment ControlsDELIMING THE GENERATOR Striker AdjustmentItems Required not provided C24GA Automatic DrainCOOKING CYCLE TEST PROBE INSPECTIONGeneral ELECTRICAL OPERATION WATER LEVEL CONTROLSSEQUENCE OF OPERATION 1.Turn power switch on A.Timer de-energized Compartment control Units after Dec SCHEMATIC DIAGRAMS Generator Schematic DiagramSchematic Diagram - Compartment Controls Standard F35425 FebruaryPage 26 of Page 27 of F35425 FebruaryCOMPONENT LOCATION CABINET BASE GENERATOR F35425 FebruaryPage 28 of COMPONENT FUNCTION CABINET BASE GENERATOR Hold Thermostat COMPONENT LOCATION COOKING COMPARTMENT Page 31 ofF35425 February COMPONENT FUNCTION COOKING COMPARTMENT TROUBLESHOOTING GeneralWater Not Being Supplied to Generator Pilot Or Main Burner Will Not LightTROUBLESHOOTING SEQUENCE OF OPERATION STEPFUNCTION DESCRIPTIONTROUBLESHOOTING CHART SYMPTOMPOSSIBLE CAUSES SYMPTOM C24GA SERIES CONVECTION STEAMERS - TROUBLESHOOTINGPOSSIBLE CAUSES SYMPTOM C24GA SERIES CONVECTION STEAMERS - TROUBLESHOOTINGPOSSIBLE CAUSES CONDENSED SPARE PARTS LIST C24GA SERIES CONVECTION STEAMERSDESCRIPTION Page 39 of F35425 February