Manuals / VXI / Kitchen Appliance / Microwave Oven

VXI SM7100, Microwave Matrix Switch Configuration, Section, FRONT PANEL CONNECTION - SM7000

Models: SM7100 Microwave Matrix

1 36

Download 36 pages 55.64 Kb

Page 15

Image 15

www.vxitech.com

SECTION 3

SWITCH CONFIGURATION

PWR/ ACC/

FAIL ERR

SM7100 EXPANDABLE

MICROWAVE SWITCH MATRIX

INPUTS

EXP INPUTS

OUTPUTS

EXPANSION OUTPUTS

FRONT PANEL CONNECTION - SM7000

This section details the SM7100 schematics, relays, and pinouts. See Section 4, Programming, for information on relay addressing.

NOTE Although pin numbers between the SM7000 and the HP equivalent differ, the signals remain in the same location. This makes it possible to use the same mating connector and cabling for either system. See Table 3-1and Figure 3-3for more information on connector J17.

EXTERNAL DRIVE

FIGURE 3-1FIGURE 3-1 SM7100 FRONT PANEL

SM7100 Module Configuration

Page 15

Image 15

VXI SM7100, Microwave Matrix user manual Switch Configuration, Section, FRONT PANEL CONNECTION - SM7000

Contents

MICROWAVE MATRIX USER’S MANUAL P/N: Released February 13, VXI Technology, Inc2031 Main Street Irvine, CA 949 SM7100VXI Technology, Inc SECTION TABLE OF CONTENTSSECTION SECTIONRESTRICTED RIGHTS LEGEND WARRANTYLIMITATION OF WARRANTY CERTIFICATIONIrvine, California D E C L A R A T I O N O F C O N F O R M I T YVXI Technology, Inc 2031 Main StreetUse Proper Power Source GENERAL SAFETY INSTRUCTIONSTERMS AND SYMBOLS Use Proper Power CordOperating Conditions WARNINGS CONTAvoid Electric Shock Ground the ProductVXI Technology Lake Stevens Instrument Division SUPPORT RESOURCESVXI Technology World Headquarters VXI Technology Cleveland Instrument DivisionINTRODUCTION SECTIONSM7100 SPECIFICATIONS SECTION PREPARATION FOR USECALCULATING SYSTEM POWER AND COOLING REQUIREMENTS SETTING THE CHASSIS BACKPLANE JUMPERSFRONT BACKFRONT BACKSM7100 Preparation for Use VXI Technology, IncSWITCH CONFIGURATION SECTIONFRONT PANEL CONNECTION - SM7000 VXI Technology, Inc SM7100 Module Configuration EXPANSION OUTPUTS FIGURE 3-4:SM7100 MATRIX SCHEMATICINPUTS EXPANSION INPUTSOffset VXI Technology, Inc SM7100 Module ConfigurationADDRESSING PROGRAMMINGREGISTER ACCESS SECTIONREAD FUNCTION TABLE 4-1:SMIP II REGISTER MAP - A16OFFSET WRITE FUNCTIONStatus Register 0x04 — Read Only ID Register 0x00 — Read OnlyLogical Address Register 0x00 — Write Only Device Type Register 0x02 — Read OnlyVersion Number Register 0x0E — Read Only Offset Register 0x06 — Read and WriteReserved Register 0x0A — Read Only Reserved Register 0x0C — Read OnlySubclass Register 0x1E — Read Only NVM Access Resister 0x20 — Read OnlyNVM Access Resister 0x20 — Write Only Interrupt Control Register 0x1C — Read and WriteTrace RAM End High Register 0x2C — Read and Write Trace RAM End Low Register 0x2E — Read and WriteTrace RAM Start Low Register 0x2A — Read and Write Open Trigger Select Register 0x36 —WriteOnly TTL Trigger Polarity Register 0x38 —WriteOnlyTrace RAM Control Register 0x3A — Read and Write Trigger Advance Register 0x3E — Write Only Board Busy Register 0x3E — Read OnlyReserved Registers — Read and Write ADDR Control Register - Read and WriteControl Register - Read and Write continued Control Register - Read and Write continued Status Register - Read Only Delay Register - Read and WriteDEVICE MEMORY MAP RELAY REGISTER OFFSETWRITING TO THE RELAYS VXI Technology, Inc INDEX WEEE VXI Technology, IncSM7100 VXIbus Extended Device