Manuals / VXI / Kitchen Appliance / Microwave Oven

VXI Microwave Matrix General Safety Instructions, Terms And Symbols, Warnings, Use Proper Fuse

Models: SM7100 Microwave Matrix

1 36

Download 36 pages 55.64 Kb

Page 6

GENERAL SAFETY INSTRUCTIONS

VXI Technology, Inc.

GENERAL SAFETY INSTRUCTIONS

Review the following safety precautions to avoid bodily injury and/or damage to the product. These precautions must be observed during all phases of operation or service of this product. Failure to comply with these precautions, or with specific warnings elsewhere in this manual, violates safety standards of design, manufacture, and intended use of the product.

Service should only be performed by qualified personnel.

TERMS AND SYMBOLS

These terms may appear in this manual:

WARNING	Indicates that a procedure or condition may cause bodily injury or death.
CAUTION	Indicates that a procedure or condition could possibly cause damage to
	equipment or loss of data.

These symbols may appear on the product:

ATTENTION - Important safety instructions

Frame or chassis ground

Indicates that the product was manufactured after August 13, 2005. This mark is placed in accordance with EN 50419, Marking of electrical and electronic equipment in accordance with Article 11(2) of Directive 2002/96/EC (WEEE). End-of-life product can be returned to VTI by obtaining an RMA number. Fees for take-back and recycling will apply if not prohibited by national law.

WARNINGS

Follow these precautions to avoid injury or damage to the product:

Use Proper Power Cord	To avoid hazard, only use the power cord specified for this product.
Use Proper Power Source	To avoid electrical overload, electric shock, or fire hazard, do not
	use a power source that applies other than the specified voltage.
Use Proper Fuse	To avoid fire hazard, only use the type and rating fuse specified for
	this product.

6	SM7100 Preface

Image 6

VXI Microwave Matrix General Safety Instructions, Terms And Symbols, Warnings, Use Proper Power Cord, Use Proper Fuse

Contents

SM7100 P/N: Released February 13, VXI Technology, Inc2031 Main Street Irvine, CA 949 MICROWAVE MATRIX USER’S MANUALVXI Technology, Inc SECTION TABLE OF CONTENTSSECTION SECTIONCERTIFICATION WARRANTYLIMITATION OF WARRANTY RESTRICTED RIGHTS LEGEND2031 Main Street D E C L A R A T I O N O F C O N F O R M I T YVXI Technology, Inc Irvine, CaliforniaUse Proper Power Cord GENERAL SAFETY INSTRUCTIONSTERMS AND SYMBOLS Use Proper Power SourceGround the Product WARNINGS CONTAvoid Electric Shock Operating ConditionsVXI Technology Cleveland Instrument Division SUPPORT RESOURCESVXI Technology World Headquarters VXI Technology Lake Stevens Instrument DivisionSECTION INTRODUCTIONSM7100 SPECIFICATIONS SETTING THE CHASSIS BACKPLANE JUMPERS PREPARATION FOR USECALCULATING SYSTEM POWER AND COOLING REQUIREMENTS SECTIONBACK FRONTBACK FRONTVXI Technology, Inc SM7100 Preparation for UseSWITCH CONFIGURATION SECTIONFRONT PANEL CONNECTION - SM7000 VXI Technology, Inc SM7100 Module Configuration EXPANSION INPUTS FIGURE 3-4:SM7100 MATRIX SCHEMATICINPUTS EXPANSION OUTPUTSOffset SM7100 Module Configuration VXI Technology, IncSECTION PROGRAMMINGREGISTER ACCESS ADDRESSINGWRITE FUNCTION TABLE 4-1:SMIP II REGISTER MAP - A16OFFSET READ FUNCTIONDevice Type Register 0x02 — Read Only ID Register 0x00 — Read OnlyLogical Address Register 0x00 — Write Only Status Register 0x04 — Read OnlyReserved Register 0x0C — Read Only Offset Register 0x06 — Read and WriteReserved Register 0x0A — Read Only Version Number Register 0x0E — Read OnlyInterrupt Control Register 0x1C — Read and Write NVM Access Resister 0x20 — Read OnlyNVM Access Resister 0x20 — Write Only Subclass Register 0x1E — Read OnlyTrace RAM End High Register 0x2C — Read and Write Trace RAM End Low Register 0x2E — Read and WriteTrace RAM Start Low Register 0x2A — Read and Write Open Trigger Select Register 0x36 —WriteOnly TTL Trigger Polarity Register 0x38 —WriteOnlyTrace RAM Control Register 0x3A — Read and Write Trigger Advance Register 0x3E — Write Only Board Busy Register 0x3E — Read OnlyReserved Registers — Read and Write Control Register - Read and Write ADDRControl Register - Read and Write continued Control Register - Read and Write continued Delay Register - Read and Write Status Register - Read OnlyDEVICE MEMORY MAP RELAY REGISTER OFFSETWRITING TO THE RELAYS VXI Technology, Inc INDEX VXIbus Extended Device VXI Technology, IncSM7100 WEEE