Manuals / Whirlpool / Kitchen Appliance / Dishwasher

Whirlpool MAH9700AW manual Door Removal, Console Removal, Disassembly Procedures

Models: MAH9700AW

1 65

Page 29

Disassembly Procedures

!	WARNING	To avoid risk of electrical shock, personal injury or
		death; disconnect power to unit before servicing.

		5.	Roll Console down and lift away from washer.

		6.	Remove Reactor wire harness from wire clip.

7. Remove Reactor wire harness connector from the PCB Board.

8. Remove five screws from PCB Housing to access the LED Circuit Board.

6. Remove fill hose clamp and hose.

Door Removal

1. Disconnect power supply to unit.

2. Remove four screws to remove door from Front Panel.

Console Removal

1.Disconnect power supply to unit.

2.Remove Top Cover.

3.Remove Dispenser Drawer.

4.Remove five screws attaching Console.

16025909 Rev. 0

Page 29

Image 29

Whirlpool MAH9700AW manual Door Removal, Console Removal, Disassembly Procedures

Contents

Service MAH9700AW27” Front Load Washer This Base Manual covers general informationCustomer Service Support Center Important Notices for Servicers and ConsumersREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Recognize Safety Symbols, Words, and LabelsComponent Testing Information TroubleshootingDisassembly Procedures 2005 Maytag ServicesRead all instructions before using the washer Important Safety Informationwhen required. Do not do it yourself unless you know how Replace worn power cords and/or loose plugsAbout Ground Wires Electrical Service InformationGeneral Information Related PublicationsImportant Safety Information Grounding InstructionsExplanation To avoid the risk of electrical shock or death, do not alter the plug16025909 Rev Important Safety InformationParts and Accessories ServiceExtended Service Plan General Information9700 Feature Package Feature ContentM A H 9 0 0 A Y W2005 Maytag Services Troubleshooting ProceduresWill Not Start LeakingWrong Water Temperature Troubleshooting Procedures2005 Maytag Services Perform Board Output Test2005 Maytag Services Troubleshooting ProceduresNoisy and/or Vibration/Walking Rubber Feet Leaving Marks on Floor2005 Maytag Services Troubleshooting ProceduresService Mode 16025909 Rev2005 Maytag Services Troubleshooting Procedures16025909 Rev Press Off twice16025909 Rev Troubleshooting Procedures2005 Maytag Services 2005 Maytag Services Troubleshooting Procedures“Whites ”and the “Rotary Cycle Selector” is 16025909 Rev2005 Maytag Services Troubleshooting Procedures“Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 16025909 Rev16025909 Rev Troubleshooting Procedures2005 Maytag Services 2005 Maytag Services Troubleshooting Proceduresspins 16025909 Rev2005 Maytag Services Troubleshooting Procedures1 Press Chime and Extra Rinse keys for 3seconds again, or 16025909 Rev2005 Maytag Services Component Testing InformationTest Procedure 16025909 Rev2005 Maytag Services Component Testing InformationCN10 ATC Control2005 Maytag Services Component Testing InformationWater flow through dispenser during Wash fill Note The heater will not turn on more than once in a2005 Maytag Services Component Testing InformationWater flow through dispenser during Rinse 1 fill 16025909 Rev2005 Maytag Services Component Testing InformationWater flow through dispenser during Rinse 2 fill 16025909 RevWater Level Sensor Removal Disassembly ProceduresTop Removal Reactor Removal Disassembly ProceduresEMI Filter Removal Dispenser Removal Water Valve RemovalCombo Cold Valve Disassembly ProceduresDisassembly Procedures Door RemovalConsole Removal 2005 Maytag Services Disassembly Procedures3. Remove hinge retainer plate 6. Remove the glass retainerDisassembly Procedures Front Panel RemovalHeater Removal Boot RemovalDisassembly Procedures 2005 Maytag ServicesDisassembly Procedures Motor RemovalDisassembly Procedures Disassembly Procedures Drain Pump Removal1x12 - 32” long Outer Tub and Spinner RemovalDisassembly Procedures 17. Remove ground wire 15.Remove Pressure Switch harness connector Disassembly Procedures2005 Maytag Services 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer Disassembly Procedures2005 Maytag Services 28.Remove screw and release tab to remove Baffles16025909 Rev Appendix A2005 Maytag Services DC68-02032B 2005 Maytag Services16025909 Rev 16025909 Rev 2005 Maytag ServicesWA RNING 2005 Maytag Services16025909 Rev LOCATION CONSIDERATIONS ALCOVE OR CLOSET INSTALLATIONDRAIN FACILITY FLOORING16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev Appendix B2005 Maytag Services 16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag ServicesT ROUBLESHOOTING INFORM ATION CODESCode Sy mbol M eani ng16025909 Rev 2005 Maytag Services