Drain Pump Removal, Disassembly Procedures | Whirlpool MAH9700AW

Drain Pump Removal

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

5. Remove wiring connector.

Drain Pump Removal

1.Disconnect power supply to unit.

2.Remove Back Cover.

3.Remove clamp and Drain Hose.

4.Remove clamp and Pump Hose.

6.Remove three 13mm bolts securing Drain Pump to base.

7.Remove screw securing Drain Pump to bracket. Twist Drain Pump clockwise to remove.

©2005 Maytag Services

16025909 Rev. 0

35

Image 35

Whirlpool MAH9700AW manual Drain Pump Removal, Disassembly Procedures

Contents

This Base Manual covers general information MAH9700AWService 27” Front Load Washer Recognize Safety Symbols, Words, and Labels Important Notices for Servicers and ConsumersCustomer Service Support Center REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS General Information TroubleshootingComponent Testing Information Disassembly Procedures Replace worn power cords and/or loose plugs Important Safety InformationRead all instructions before using the washer when required. Do not do it yourself unless you know how Related Publications Electrical Service InformationAbout Ground Wires General Information To avoid the risk of electrical shock or death, do not alter the plug Grounding InstructionsExplanation 16025909 Rev General Information ServiceParts and Accessories Extended Service Plan 0 0 A Y W Feature Content9700 Feature Package M A H 9 No Tumble Troubleshooting ProceduresWill Not Start Leaking Will Not Lock Perform Board Output TestWet Clothes See Will Not Spin Buttons do not Respond Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Additive Cups Full of Water Press Off exits Service Mode Press Spin Press Off twicecounterclockwis 16025909 Rev “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 16025909 Rev Go to Door Lock spinsMembrane Pad taken 1 Press Chime and Extra Rinse keys for 3seconds again, orCode Component Component Testing InformationTest Procedure Illustration ATC Control CN10 WASH Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a wash cycle no reheating RINSE Water flow through dispenser during Rinse 1 fill RINSE Water flow through dispenser during Rinse 2 fill Water Level Sensor Removal Disassembly ProceduresTop Removal Reactor Removal Disassembly ProceduresEMI Filter Removal Hot Valve Water Valve RemovalDispenser Removal Combo Cold Valve Console Removal Door Removal 6. Remove the glass retainer Disassembly Procedures2005 Maytag Services 3. Remove hinge retainer plate Front Panel Removal 2005 Maytag Services Boot RemovalHeater Removal Motor Removal Disassembly Procedures Drain Pump Removal 1x12 - 32” long Outer Tub and Spinner Removal 16. Remove the Pressure Hose 14.Remove fill hose 17. Remove ground wire 15.Remove Pressure Switch harness connector Disassembly Procedures Disassembly Procedures 28.Remove screw and release tab to remove Baffles 27.Lift Spinner to access Wave Washer Appendix A DC68-02032B 16025909 Rev WA RNING FLOORING ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS DRAIN FACILITY 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev Appendix B 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev 2005 Maytag Services 16025909 Rev M eani ng INFORM ATION CODEST ROUBLESHOOTING Code Sy mbol 16025909 Rev 2005 Maytag Services