Manuals / Whirlpool / Kitchen Appliance / Dishwasher

Whirlpool MAH9700AW manual Disassembly Procedures

Models: MAH9700AW

1 65

Download 65 pages 23.43 Kb

Page 39

Image 39

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

NOTE: Torque tub bolts to 6-11 ft. lbs.

25. Separate the front and rear halves of the Outer Tub.

23.Set the tub on the floor. Position 4" wood blocks or equivalent around the spinner shaft. Roll the tub to the upright position and rest it on the blocks.

24.Remove the 10mm screws around the perimeter of the tub.

26. Tub Gasket can be replaced after tub halves are split.

16025909 Rev. 0

Page 39

Image 39

Whirlpool MAH9700AW manual Disassembly Procedures

Contents

This Base Manual covers general information MAH9700AWService 27” Front Load WasherRecognize Safety Symbols, Words, and Labels Important Notices for Servicers and ConsumersCustomer Service Support Center REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS2005 Maytag Services TroubleshootingComponent Testing Information Disassembly ProceduresReplace worn power cords and/or loose plugs Important Safety InformationRead all instructions before using the washer when required. Do not do it yourself unless you know howRelated Publications Electrical Service InformationAbout Ground Wires General InformationTo avoid the risk of electrical shock or death, do not alter the plug Grounding InstructionsImportant Safety Information Explanation16025909 Rev Important Safety InformationGeneral Information ServiceParts and Accessories Extended Service Plan0 0 A Y W Feature Content9700 Feature Package M A H 9Leaking Troubleshooting Procedures2005 Maytag Services Will Not StartPerform Board Output Test Troubleshooting ProceduresWrong Water Temperature 2005 Maytag ServicesRubber Feet Leaving Marks on Floor Troubleshooting Procedures2005 Maytag Services Noisy and/or Vibration/Walking16025909 Rev Troubleshooting Procedures2005 Maytag Services Service ModePress Off twice Troubleshooting Procedures2005 Maytag Services 16025909 RevTroubleshooting Procedures 2005 Maytag Services16025909 Rev 16025909 Rev Troubleshooting Procedures2005 Maytag Services “Whites ”and the “Rotary Cycle Selector” is16025909 Rev Troubleshooting Procedures2005 Maytag Services “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water levelTroubleshooting Procedures 2005 Maytag Services16025909 Rev 16025909 Rev Troubleshooting Procedures2005 Maytag Services spins16025909 Rev Troubleshooting Procedures2005 Maytag Services 1 Press Chime and Extra Rinse keys for 3seconds again, or16025909 Rev Component Testing Information2005 Maytag Services Test ProcedureATC Control Component Testing Information2005 Maytag Services CN10Note The heater will not turn on more than once in a Component Testing Information2005 Maytag Services Water flow through dispenser during Wash fill16025909 Rev Component Testing Information2005 Maytag Services Water flow through dispenser during Rinse 1 fill16025909 Rev Component Testing Information2005 Maytag Services Water flow through dispenser during Rinse 2 fillDisassembly Procedures Top RemovalWater Level Sensor Removal Disassembly Procedures EMI Filter RemovalReactor Removal Disassembly Procedures Water Valve RemovalDispenser Removal Combo Cold ValveDoor Removal Console RemovalDisassembly Procedures 6. Remove the glass retainer Disassembly Procedures2005 Maytag Services 3. Remove hinge retainer plateDisassembly Procedures Front Panel Removal2005 Maytag Services Boot RemovalHeater Removal Disassembly ProceduresDisassembly Procedures Motor RemovalDisassembly Procedures Disassembly Procedures Drain Pump RemovalOuter Tub and Spinner Removal Disassembly Procedures1x12 - 32” long 16. Remove the Pressure Hose 14.Remove fill hose Disassembly Procedures17. Remove ground wire 15.Remove Pressure Switch harness connector 2005 Maytag ServicesDisassembly Procedures Disassembly Procedures 28.Remove screw and release tab to remove Baffles Disassembly Procedures27.Lift Spinner to access Wave Washer 2005 Maytag ServicesAppendix A 2005 Maytag Services16025909 Rev 2005 Maytag Services 16025909 RevDC68-02032B 16025909 Rev 2005 Maytag Services2005 Maytag Services 16025909 RevWA RNING FLOORING ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS DRAIN FACILITY16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag ServicesAppendix B 2005 Maytag Services16025909 Rev 16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag ServicesM eani ng INFORM ATION CODEST ROUBLESHOOTING Code Sy mbol16025909 Rev 2005 Maytag Services