Manuals / Whirlpool / Kitchen Appliance / Dishwasher

Whirlpool MAH9700AW manual Disassembly Procedures

Models: MAH9700AW

1 65

Download 65 pages 23.43 Kb

Page 34

Image 34

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

5. Remove 19mm nut .

NOTE: When reinstalling Motor torqe nut to 32-47 ft. lbs.

6.Grasp the Rotor at 3 and 9 o’clock while pulling Rotor from shaft.

CAUTION: The rotor contains powerful magnets. Use caution during handeling and installation. DO NOT place fingers between rotor and windings during installation.

7.Depress and release latch to remove motor wiring connectors.

8.Remove the six 10mm bolts securing stator coil to the tub.

NOTE: There are alignment pins for the Stator reinstallation. Use caution during removal and installtion, the stastor will not hang from the alignment pins. Start a screw while supporting the Stator with the other hand.

34	16025909 Rev. 0

Page 34

Image 34

Whirlpool MAH9700AW manual Disassembly Procedures

Contents

27” Front Load Washer MAH9700AWService This Base Manual covers general informationREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Important Notices for Servicers and ConsumersCustomer Service Support Center Recognize Safety Symbols, Words, and LabelsDisassembly Procedures TroubleshootingComponent Testing Information 2005 Maytag Serviceswhen required. Do not do it yourself unless you know how Important Safety InformationRead all instructions before using the washer Replace worn power cords and/or loose plugsGeneral Information Electrical Service InformationAbout Ground Wires Related PublicationsExplanation Grounding InstructionsImportant Safety Information To avoid the risk of electrical shock or death, do not alter the plugImportant Safety Information 16025909 RevExtended Service Plan ServiceParts and Accessories General InformationM A H 9 Feature Content9700 Feature Package 0 0 A Y WWill Not Start Troubleshooting Procedures2005 Maytag Services Leaking2005 Maytag Services Troubleshooting ProceduresWrong Water Temperature Perform Board Output TestNoisy and/or Vibration/Walking Troubleshooting Procedures2005 Maytag Services Rubber Feet Leaving Marks on FloorService Mode Troubleshooting Procedures2005 Maytag Services 16025909 Rev16025909 Rev Troubleshooting Procedures2005 Maytag Services Press Off twice2005 Maytag Services Troubleshooting Procedures16025909 Rev “Whites ”and the “Rotary Cycle Selector” is Troubleshooting Procedures2005 Maytag Services 16025909 Rev“Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level Troubleshooting Procedures2005 Maytag Services 16025909 Rev2005 Maytag Services Troubleshooting Procedures16025909 Rev spins Troubleshooting Procedures2005 Maytag Services 16025909 Rev1 Press Chime and Extra Rinse keys for 3seconds again, or Troubleshooting Procedures2005 Maytag Services 16025909 RevTest Procedure Component Testing Information2005 Maytag Services 16025909 RevCN10 Component Testing Information2005 Maytag Services ATC ControlWater flow through dispenser during Wash fill Component Testing Information2005 Maytag Services Note The heater will not turn on more than once in aWater flow through dispenser during Rinse 1 fill Component Testing Information2005 Maytag Services 16025909 RevWater flow through dispenser during Rinse 2 fill Component Testing Information2005 Maytag Services 16025909 RevTop Removal Disassembly ProceduresWater Level Sensor Removal EMI Filter Removal Disassembly ProceduresReactor Removal Combo Cold Valve Water Valve RemovalDispenser Removal Disassembly ProceduresConsole Removal Door RemovalDisassembly Procedures 3. Remove hinge retainer plate Disassembly Procedures2005 Maytag Services 6. Remove the glass retainerFront Panel Removal Disassembly ProceduresDisassembly Procedures Boot RemovalHeater Removal 2005 Maytag ServicesMotor Removal Disassembly ProceduresDisassembly Procedures Drain Pump Removal Disassembly ProceduresDisassembly Procedures Outer Tub and Spinner Removal1x12 - 32” long 2005 Maytag Services Disassembly Procedures17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 2005 Maytag Services Disassembly Procedures27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove Baffles2005 Maytag Services Appendix A16025909 Rev 16025909 Rev 2005 Maytag ServicesDC68-02032B 2005 Maytag Services 16025909 Rev16025909 Rev 2005 Maytag ServicesWA RNING DRAIN FACILITY ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B16025909 Rev 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 RevCode Sy mbol INFORM ATION CODEST ROUBLESHOOTING M eani ng2005 Maytag Services 16025909 Rev