Manuals / Woods Equipment / Lawn and Garden / Lawn Mower

Woods Equipment MX54T, MX61T manual Pre-Operation Check List

Models: MX54T MX61T

1 52

Download 52 pages 17.78 Kb

Page 15

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___	Review and follow all safety rules and safety
	decal instructions on page 5 through page 8.
___	Check that all safety decals are installed and in
	good condition. Replace if damaged.
___	Check to make sure all shields and guards are
	properly installed and in good condition. Be sure
	that either the discharge chute, mulching end
	cap, or complete vacuum attachment is installed.
___	Check that all hardware and cotter pins are prop-
	erly installed and secure.
___	Check to ensure blades are sharp, in good condi-
	tion, and installed correctly. Replace if damaged.
___	Check that equipment is properly and securely
	attached to power unit.
___	Do not allow riders.
___	Inspect area and remove stones, branches or
	other hard objects that might be thrown, causing
	injury or damage.

___ Check engine oil level. Clean area around oil fill dipstick. Remove dipstick and check to be sure oil is in operating range (between marks on dip- stick). Add oil if necessary but Do Not Overfill. Install Dipstick assembly firmly until cap bottoms out on tube. Dipstick assembly must always be secured into fill tube when engine is running.

___ Check all lubrication points and grease as instructed in Lubrication, page 16.

___ Perform a functional check of the safety interlock system each time you operate the unit. Place both steering levers outward, start engine, engage PTO and then rise up out of the seat. The engine should die when you raise up. If it does not, do not operate unit until the safety interlock system has been repaired and operates properly.

____ Check that the PowerTilt™ deck safety switch is

working properly. While sitting in the seat, with the engine running, raise the deck to a partially tilted position and move a traction arm out of neu- tral. The engine should shut off. Repeat the same steps with the deck in the cutting height range. The engine should continue to run with the trac- tion arms moved out of neutral.

MAN0253 (Rev. 3/10/2007)	Operation 15

Image 15

Woods Equipment MX54T, MX61T manual Pre-Operation Check List

Contents

Manual Lift Models MX54 & MX61 PowerTilt Models MX54T & MX61T MAN0253OPERATORS MANUAL TO THE OWNER 2 IntroductionSerial Number see Safety Decal section for location TO THE DEALERTABLE OF CONTENTS IntroductionLEA EL INSTRUCTIVO SPECIFICATIONS 4 IntroductionGENERAL INFORMATION TRAINING SafetySAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVEDSAFETY RULES 6 SafetyMAINTENANCE STORAGESafety SAFETY & INSTRUCTIONAL DECALSReplace Immediately If Damaged MX54 & MX61ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED 8 SafetyBE CAREFUL SAFETY & INSTRUCTIONAL DECALSATTACHING MOWER TO POWER UNIT OperationOPERATION CUTTING HEIGHT ADJUSTMENT PowerTilt Operation Figure 3 & Figure10 Operation Operation MOWER SIDE-TO-SIDE ADJUSTMENT12 Operation MOWING TIPSSTORAGE Continued TROUBLESHOOTINGMOWING CONDITIONS OperationTROUBLESHOOTING 14 OperationMOWING CONDITIONS Continued BELT CONDITIONSOperation PRE-OPERATION CHECK LIST16 Service SERVICELUBRICATION Blade Removal ServiceBLADE SERVICE Blade InstallationBelt Replacement 18 ServiceBELT SERVICE Belt Adjustment FigureSPINDLE REPAIR Figure Spindle Removal Spindle DisassemblySpindle Assembly REAR PIVOT LIFT ARM SERVICE20 Service CASTER WHEEL MAINTENANCELIFT LINKAGE BUSHING REPLACEMENT Service CLEANING After Each UsePeriodically or Before Extended Storage RETURNING TO OPERATIONDEALER SET-UP INSTRUCTIONS 22 AssemblyASSEMBLY INSTRUCTIONS Mower Assembly FigureAssembly Install Discharge Chute FigureATTACHING MOWER TO POWER UNIT Preparation - All Models Wiring Connections MXT Deck SN 1100886 and above 24 AssemblyDP3T AssemblyFZ Series Power Units without timer delay Figure F Series Power Units FigureDeck Attachment - All Models 26 AssemblyAssembly ADJUST CUTTING HEIGHTApply Deck Height Decal - PowerTilt Units ADJUST MOWER SIDE-TO-SIDEFigure 29. Height Adjustment Linkage - MC54/MX61 28 AssemblyFigure 30. Height Adjustment Linkage - PowerTilt Models AssemblyDELIVERY CHECK LIST 30 Dealer Check ListsDEALER CHECK LISTS PRE-DELIVERY CHECK LISTPARTS INDEX PartsModels MX54 & MX61 MX54T & MX61T with PowerTilt MOW’N MACHINE MOWER DECKDecal Set MX54 & MX61 DECK ASSEMBLY32 Parts 59 - SafetyParts MX54 & MX61 DECK ASSEMBLY PARTS LIST34 Parts MX54T & MX61T DECK ASSEMBLY WITH POWERTILTParts MX54T & MX61T DECK ASSEMBLY WITH POWERTILTMX54T/MX61T SIMILAR 36 PartsDECK DRIVE SYSTEM MX54/MX61 SHOWNParts DECK DRIVE SYSTEM PARTS LIST38 Parts RIGHT ANGLE GEARBOX ASSEMBLY1/4-28 Tapered thread grease fitting FLOATING DECK LIFT ARMParts Tension bushing 1-1/4 x 1-1/2 x 1-1/240 Parts POWERTILT ASSEMBLYHEIGHT ADJUSTMENT HANDLE ASSEMBLY PartsFOR MX54/MX61 MANUALLY CONTROLLED CUTTING HEIGHT 42 Parts WHEEL LIFT ASSEMBLY1001513KT BLADE SPINDLE ASSEMBLYParts Spindle bearing, 25 mm no sealMULCH KIT 44 PartsPOWERTILT F SERIES WIRING DIAGRAM DECK SN 1100885 & BELOW NO TIMER DELAYParts POWERTILT WITH TIMER DELAY 46 PartsFZ SERIES Appendix BOLT TORQUE CHARTSAE SERIES A TORQUE CHART CHARTSAE Bolt Thread Sizes BOLT SIZE CHART48 Appendix ABBREVIATIONSIndex AssemblySafety ServiceWHAT IS NOT COVERED LIMITED WARRANTYMow’n MachineTM Zero-Turn Mowers WHAT IS COVEREDF-8494 Rev. 6/23/2005 WARRANTY2606 South Illinois Route Post Office Box Oregon, Illinois 61061 USA Woods Equipment Company