Manuals / Woods Equipment / Lawn and Garden / Lawn Mower

Woods Equipment MX61T, MX54T manual Assembly, Wiring Connections MXT Deck SN 1100886 and above

Models: MX54T MX61T

1 52

Download 52 pages 17.78 Kb

Page 24

Wiring Connections

Figure 20. Wiring Connection - MXT Deck (SN 1100886 & above)

Wiring Connections

MXT Deck SN 1100886 and above

1.Lift seat/hood and remove jumper (75521) from power unit’s main wire harness. (Located on front left side by steering pivot.) Keep jumper; power unit will not operate unless jumper or deck is attached.

2.Connect free end of deck safety harness to power unit’s main wire harness where jumper was previ- ously attached. Route harness through steering pivot slot (weatherpack connector).

3.Connect free end of deck actuator harness to power unit’s main wire harness. Route harness through steering pivot slot. The main wire harness connector is located underneath seat/hood by front left steering pivot. (Packard 56 series connector.)

4.Tie strap harnesses to front of power unit frame. Make sure wires are not pinched by steering link-

age during operation. Wire must also remain clear of tire and not pull tight during tilt operation or deck tilting side to side.

Connect Wiring Harness - PowerTilt™ Units MXT Deck SN 1100885 and below

NOTE: If you plan to use the MXT deck with the actua- tor switch mounted on the deck, you must determine which wire harness to use. Select harness 75407 for FZ power units. Select harness 75433 for F-series power units. These harnesses are provided with MXT decks having SN 1100885 and below.

1.Attach red and black wires from the power tilt cable (75407 or 75433) to the center terminals of the rocker switch as shown in Figure 21.

2.Insert opposite end of power tilt cable through left steering handle slot as shown in Figure 22.

24Assembly

(Rev. 1/11/2008)

MAN0253 (Rev. 3/10/2007)

Image 24

Woods Equipment MX61T, MX54T manual Assembly, Wiring Connections MXT Deck SN 1100886 and above

Contents

Manual Lift Models MX54 & MX61 PowerTilt Models MX54T & MX61T MAN0253OPERATORS MANUAL 2 Introduction Serial Number see Safety Decal section for locationTO THE DEALER TO THE OWNERTABLE OF CONTENTS IntroductionLEA EL INSTRUCTIVO SPECIFICATIONS 4 IntroductionGENERAL INFORMATION Safety SAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED TRAINING6 Safety MAINTENANCESTORAGE SAFETY RULESSAFETY & INSTRUCTIONAL DECALS Replace Immediately If DamagedMX54 & MX61 Safety8 Safety BE CAREFULSAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVEDATTACHING MOWER TO POWER UNIT OperationOPERATION CUTTING HEIGHT ADJUSTMENT PowerTilt Operation Figure 3 & Figure10 Operation MOWER SIDE-TO-SIDE ADJUSTMENT Operation12 Operation MOWING TIPSSTORAGE TROUBLESHOOTING MOWING CONDITIONSOperation Continued14 Operation MOWING CONDITIONS ContinuedBELT CONDITIONS TROUBLESHOOTINGPRE-OPERATION CHECK LIST Operation16 Service SERVICELUBRICATION Service BLADE SERVICEBlade Installation Blade Removal18 Service BELT SERVICEBelt Adjustment Figure Belt ReplacementSpindle Disassembly Spindle AssemblyREAR PIVOT LIFT ARM SERVICE SPINDLE REPAIR Figure Spindle Removal20 Service CASTER WHEEL MAINTENANCELIFT LINKAGE BUSHING REPLACEMENT CLEANING After Each Use Periodically or Before Extended StorageRETURNING TO OPERATION Service22 Assembly ASSEMBLY INSTRUCTIONSMower Assembly Figure DEALER SET-UP INSTRUCTIONSAssembly Install Discharge Chute FigureATTACHING MOWER TO POWER UNIT Preparation - All Models 24 Assembly Wiring Connections MXT Deck SN 1100886 and aboveAssembly FZ Series Power Units without timer delay FigureF Series Power Units Figure DP3T26 Assembly Deck Attachment - All ModelsADJUST CUTTING HEIGHT Apply Deck Height Decal - PowerTilt UnitsADJUST MOWER SIDE-TO-SIDE Assembly28 Assembly Figure 29. Height Adjustment Linkage - MC54/MX61Assembly Figure 30. Height Adjustment Linkage - PowerTilt Models30 Dealer Check Lists DEALER CHECK LISTSPRE-DELIVERY CHECK LIST DELIVERY CHECK LISTParts Models MX54 & MX61 MX54T & MX61T with PowerTiltMOW’N MACHINE MOWER DECK PARTS INDEXMX54 & MX61 DECK ASSEMBLY 32 Parts59 - Safety Decal SetMX54 & MX61 DECK ASSEMBLY PARTS LIST PartsMX54T & MX61T DECK ASSEMBLY WITH POWERTILT 34 PartsMX54T & MX61T DECK ASSEMBLY WITH POWERTILT Parts36 Parts DECK DRIVE SYSTEMMX54/MX61 SHOWN MX54T/MX61T SIMILARDECK DRIVE SYSTEM PARTS LIST PartsRIGHT ANGLE GEARBOX ASSEMBLY 38 PartsFLOATING DECK LIFT ARM PartsTension bushing 1-1/4 x 1-1/2 x 1-1/2 1/4-28 Tapered thread grease fittingPOWERTILT ASSEMBLY 40 PartsHEIGHT ADJUSTMENT HANDLE ASSEMBLY PartsFOR MX54/MX61 MANUALLY CONTROLLED CUTTING HEIGHT WHEEL LIFT ASSEMBLY 42 PartsBLADE SPINDLE ASSEMBLY PartsSpindle bearing, 25 mm no seal 1001513KT44 Parts MULCH KITPOWERTILT F SERIES WIRING DIAGRAM DECK SN 1100885 & BELOW NO TIMER DELAYParts POWERTILT WITH TIMER DELAY 46 PartsFZ SERIES BOLT TORQUE CHART SAE SERIES A TORQUE CHARTCHART AppendixBOLT SIZE CHART 48 AppendixABBREVIATIONS SAE Bolt Thread SizesAssembly SafetyService IndexLIMITED WARRANTY Mow’n MachineTM Zero-Turn MowersWHAT IS COVERED WHAT IS NOT COVEREDWARRANTY F-8494 Rev. 6/23/2005Woods Equipment Company 2606 South Illinois Route Post Office Box Oregon, Illinois 61061 USA