Using the Tailstock | Woodstock M1049 manual

D('+09\eZ_kfgCXk_\D]^%J`eZ\/&'0

Using the Tailstock

The tailstock (Figure 18) can be used to support workpieces with the use of a live or dead center. Using an MT#2 drill chuck and a drill bit, the lathe can drill or bore holes in the center of a part. The tailstock can also be offset for cutting shallow tapers.

To use the tailstock, do these steps:

1.Slide the tailstock to the desired position.

2.Tighten the tailstock lock nut to lock the tailstock in place on the ways.

3.With the tailstock locked, turn the quill lock lever to unlock the quill.

4.Turn the quill feed handle clockwise to feed/move the quill towards the spindle, or counterclockwise to move away from the spindle.

	Quill Lock Lever
Tailstock
Lock Nut
	Scale
Offset Adjustment	Quill Feed
Offset Adjustment

Figure 18. Tailstock controls.

5.Turn the quill lock lever to lock the quill in place.

FG<I8K@FEJ

-23-

Image 25

Woodstock M1049 manual Using the Tailstock, To use the tailstock, do these steps

Contents

7C8=IDEA6I= Page Table of Contents JIM@ D8@EKE8E FGI8K@FEJ JKLG G8IKJ Woodstock Technical Support Introduction @EKIFLK@FE @EKIFLK@FE @EKIFLK@FE Controls and Features For Your Own Safety Read Manual Before Operating Machine Safety J8=KP Additional Safety Instructions for Lathes Avoiding Potential Injuries Circuit Requirements ElectricalAmps Nema Extension Cords Grounding Requirements50 ft Installed Accessories Figure Qty SetupPackaged Accessories Figure Inventory Cleaning Machine Machine Placement JKLG Uncrating & Lifting Test Run and Break-In To begin the test run procedure, do these steps General Lathe Operations Chuck and Faceplate Mounting Disconnect Power to the Lathe To remove a set of jaws, do these steps Replacing Jaws To install the four-jaw chuck, do these steps Using the Four-Jaw ChuckTo load a workpiece in the four-jaw chuck, do these steps To install the faceplate, do these steps Using the Faceplate To use the tailstock, do these steps Using the Tailstock Tailstock Alignment To setup the tailstock to cut tapers, do these stepsTo align the tailstock, do these steps =`li\22% Tailstock adjustment option #2 Using Centers Using the Follow Rest Using the Steady RestTo use the steady rest, do these steps Using the Tool Posts Setting Compound SlideTo set the angular position, do these steps Longitudinal Handwheel Using Manual Feed To determine and set the needed cutting RPM, do these steps Setting RPMCutting Speeds for High Speed Steel HSS Cutting Tools RPM Chart To set and engage the power feed, do these steps Setting Power Feed Rate To setup for threading, do these steps Threading Setup General Maintenance MaintenanceGeneral Cleaning General Lubrication =`li\43%End-cap bushing and tailstock Ball oilers Cross-Slide and Saddle Gib Adjustments ServiceCross Slide Backlash Replacing the Cogged Belt Replacing the V-BeltTo replace the V-belt, do these steps To replace the cogged-belt, do these steps HL8C@=@CKI@@8E% Due to Electrical Safety Instructions Stop Wiring Diagram Motor & Electrical Troubleshooting Operation and Work Results +09\eZkfgCXk\D%J`eZ\/&0 Drive Belt Parts Belt Tensioner Change Gears Headstock Quick-Change Gearbox Front View Apron Apron Parts List Saddle & Cross Slide Compound Rest & Tool Post Tailstock Follow Rest Steady Rest Bed XPS09M Electrical & Tools Grouped Warnings Label Machine LabelsPage Page Page Place Stamp Here N8II8EKP =\FjVainBVXcZhVcYIddah