D('+09\eZ_kfgCXk_\D]^%J`eZ\/&'0

:lkk`e^J_XccfnKXg\ij n`k_k_\KX`cjkfZb

To setup the tailstock to cut tapers, do these steps:

1.Lock the tailstock in position.

2.Alternately loosen and tighten the left and right offset adjustment screws until the desired offset is indicated on the scale (see Figure 19).

3.Retighten the lock screw.

 Efk\1 Kfi\kliek_\kX`cjkfZbYXZbkfk_\fi`^`eXc gfj`k`fe#i\g\Xkk_\gifZ\jjlek`ck_\Z\ek\i\[ gfj`k`fe`j`e[`ZXk\[fek_\jZXc\%

Left Offset

Adjustments

Scale

=`^li\19% Left offset adjustment.

FG<I8K@FEJ

Tailstock Alignment

The tailstock is aligned at the factory with the headstock. We recommend that you take the time to ensure that the tailstock is aligned to your own desired tolerances.

To align the tailstock, do these steps:

1.

Get two pieces of steel round stock, two inches in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

diameter and six inches long.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Center drill both ends of one piece of the round

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

stock.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Using the other piece of stock, make a dead center

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

=`^li\20% Tailstock centering dead center.

 

by turning a shoulder to make a shank. Flip the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

piece over in the chuck and turn a 60º point (see

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 20).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: 8jcfe^Xjk_\[\X[Z\ek\ii\dX`ej`ek_\

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Z_lZb#k_\gf`ekf]pfliZ\ek\in`cci\dX`ekil\kf

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

k_\jg`e[c\Xo`j%B\\g`ed`e[k_Xkk_\gf`ekn`cc

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

_Xm\kfY\i\]`e`j_\[n_\e\m\i`k`ji\dfm\[Xe[

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

i\klie\[kfk_\Z_lZb%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Place the live center in the tailstock.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.

Attach a lathe dog to the bar stock and mount it

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

between centers.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Turn approximately 0.010" off the diameter.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-24-

Page 26
Image 26
Woodstock M1049 manual Tailstock Alignment, To setup the tailstock to cut tapers, do these steps