Xantrex Technology FP 3000-12 Fleet Power

SPECIFICATIONS

Fleet Power 3000-12

Nominal Battery Charge

Battery Voltage Range

Low Battery Cutout

AC Input Voltage Range

Frequency Regulation

Inverter Output Power (Continuous)

Inverter Voltage Regulation

Wave Shape

Surge Power

No Load Current Drain (Idle Mode) Power Factors Allowed

Full Load Efficiency

Peak Efficiency

Protection

Charging Rate

AC Input (Max. Charge Mode) Bulk Charge Voltage

Float Charge Voltage

Equalizing Charge Voltage

Status Panel

Weight

Dimensions

12 VDC

10.0to 15.5 VDC

10.0VDC (+/- 0.5)

Minimum 90 VAC/Normal 130 VAC 50 or 60 Hz Quartz Regulated 3000 VA

120 V +/- 5% true RMS Modified Sine Wave 75 amps

.12 amps All

86% (60 Hz)

93%

Over/under utility voltage, over/under battery voltage, short circuit, circuit breaker, over temperature, backfeed

140 amps (three stage)

28amps 14.3 VDC* 13.4 VDC* 16.3 VDC* Optional remote

50lbs.

13.2'' L x 11.5'' W x 7.9'' H

*variable on unit with Temperature Sensor installed and adjustable by Battery Type selected on the inverter/charger control panel or from the Remote Control Panel.

35

Contents

Page www.xantrex.com Introduction Troubleshooting Things You Should Know Glossary Warranty 1.DC to AC power inverting 2.Automatic transfer switching between inverter power and incoming AC power 3.Automatic three-stagebattery charging plus manual battery equalizing Electronic Protection Circuit Breaker Protection Thermostat Controlled Cooling Inverter Idle Circuit Low and High Battery Shutdown Power Sharing Temperature Sensitive Charging (TSC) External AC Power Front Panel Controls and Indicators INVERT MODE CHARGE MODE •Turn the charger ON and OFF STATUS LEDs Battery Type Selection Operation Status INVERT CHARGE LOW BATTERY & OVERTEMP/OVERLOAD TSC (Temperature Sensitive Charging) OPTIONAL REMOTES not Remote Control Panel Page Series Parallel AMP-HOURCONSUMPTION FORMULAS (AC amps x 10) x 1.1 x hours of operation = DC amp hours (watts/ DC voltage) x 1.1 x hours of operation = DC amp hours (AC VA/ DC voltage) x 1.1 x hours of operation = DC amp hours Typical Power Consumptlon Fleet Power Battery Chargers The battery charger stages are: Stage 1 Bulk Charge Stage Stage Stage 4 Removal of residual sulfate 2.Bring all cells to the same potential Mixing up of the electrolyte 1.Do not equalize gel cell batteries. Check remote default settings Always monitor the equalize charge cycle 3.Check the battery electrolyte both With the Remote Control Panel Page Page Page Do not backfeed the AC output of the in- verter with incoming AC power Always use proper wire and connectors make sure these do not operate from the inverter output AC power When using a Remote Control Panel, the jumper is not used Grounding Neutral Bonding AC Wiring AC Input: AC Output: Dual AC Output Ground Fault Circult Interrupters Pass & Seymour Catalog Number Rated: 15 Amps at 120 Volts AC Remote Control Wiring Page Battery Cable Fusing Recommended Fuse: UL Listed Class T JLLN not 1.Test the inverter function: 2.Test the transfer function: 3.Test the battery charger function: Page Page Alternating Current (AC) Ampere (amp, A) Amp hour (Amp-Hr Ah) GFCI (Ground Fault Circuit Interrupter) Ground LED (Light Emitting Diode) Indicator light NEC Negative Fleet Power Page Installation examples for the FP3000-12 Shorepower configurations: Inverter/charger configuration: FP3000-12DC Cable and Fuse General Guide Installation Option #1 Page Installation Option #2 Page Page What does this warranty cover What will Xantrex do How do you get service Disclaimer Product Return Material Authorization Policy Return Procedure If you are returning a product from outside of the USA or Canada If you are returning a product to a Xantrex Authorized Service Center (ASC)