Yamaha LSP - page 33

LS9 Editor Owner’s Manual

33

HKNEE

Speciﬁes the sharpness at which the output level will change. You can select from HARD or 1–5.

IATTAC K

Speciﬁes the time from when the key-in signal exceeds the threshold level until the signal starts being compressed.

JGAIN

Adjusts the gain of the signal after it has passed through the compressor.

KRELEASE

Speciﬁes the time from when the key-in signal falls below the threshold level until compression is removed.

LKEY IN SOURCE

Click this to select the key-in signal that you want to use.

The choices are the same as for GATE.

If COMPANDER-H, COMPANDER-S is selected

ATYPE

Indicates the type of the currently selected compressor. You can click here to select the type.

BLIBRARY

This button accesses the dynamics library. Clicking this button will open the DYNAMICS page of the LIBRARY

window.

CON

This button switches the compressor on/off.

DResponse curve

Indicates the response for the compander of the currently selected channel.

EGR meter

This meter indicates the amount of gain reduction produced by the compressor.

FTHRESHOLD

Speciﬁes the threshold level at which the compressor will operate. The input signal will start being compressed

when the key-in signal exceeds this level; compression will be removed when the signal falls below this level.

GRATIO

Speciﬁes the ratio at which the input signal will be compressed when the key-in signal exceeds the threshold.

HWIDTH

Speciﬁes the width between the threshold level of the compressor (THRESHOLD) and the threshold level of the

expander. The expander effect will apply to levels below THRESHOLD + WIDTH.

1

4

L

2 35

J

7

8

6

9

K

Contents

Main Special Notices Yamaha Pro Audio Global Site Contents Overview of LS9 Editor System Setup Conguring LS9 Editor Getting Started Mixer Setup Creating a user key H CH OPERATION CURRENT SCENE L FILE LOAD Working with Sessions Undo/Redo Function Window operations Synchronizing LS9 Editor Ofine Edit Function Basic operation of controllers Knobs Faders Numerical displays only Bar graphs CHANNEL SELECT SYNC Master window SCENE MEMORY Layer Keys Page INPUT CH window AInput patch BHA GAIN C48V Overview window 1 2 3 Page Page ST IN window Page MIX window Page MATRIX window Page STEREO/MONO window Page Custom Fader Layer window Custom Fader Layer window Custom Fader Layer ST IN window If an input channel is selected Selected Channel window Page MIX SEND HA GAIN//HPF TO STEREO/MONO MODE ST/MONO button LCR button EQUALIZER DYNAMICS1/2 Page Page Page INSERT (INPUT CH 132 only) DIRECT OUT (except for ST IN CH) RECALL SAFE/MUTE SAFE MUTE GROUP Fader If a MIX channel is selected TO MATRIX TO STEREO/MONO Here you can specify how the signal will be sent from the MIX channel to the STEREO bus / MONO bus. MODE ST/MONO button When this button is on, the signal will be sent to the STEREO bus and independently to the MONO bus. LCR button EQUALIZER Page If a MATRIX channel is selected FROM MIX, ST/MONO AFROM MIX, ST/MONO send level PRE/POST BON(FROM MIX, ST/MONO send on/off) Page Page Page Library window Page Page Patch Editor window INPUT PATCH page PRESET CLEAR ALL Page Page PATCH LIST page Page AMount BInput patch CModule graphic DInput meter/Output meter EOutput patch Rack module editor GEQ window CInput patch DInput meter 5 3 4 EOutput patch Page Page Page Page EXTERNAL HA page INPUT METER page Meter window OUTPUT METER page CUSTOM FADER LAYER METER page MUTE GROUP ASSIGN page Group/Link window CHANNEL LINK page Page SCENE MEMORY page Scene window Page Page RECALL SAFE page Page FADE TIME page Page Current User Edit User Select Channel ID CLEAR ALL Custom Fader Layer Setup window Current User Edit User Select Function name User Dened Keys Setup window Keyboard Shortcuts REV-X HALL/REV-X ROOM/REV-X PLATE Part Names and Functions AEFFECT NAME The effects name appears here. Appendix F[Room Size] G[Diffusion] H[HPF] I[LPF] J[Hi Ratio] Page Index B C D E