Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha pmn ■About the test tone, E-60, 2 LOW FREQ.TEST

1 128

Download 128 pages, 9.07 Mb

SET MENU ITEMS

1 SPEAKER SET

Set the speaker mode depending on your speaker system. See “SPEAKER MODE SETTINGS” on pages __ to __ for details about the setting items.

2 LOW FREQ. TEST

Use this feature to adjust the output level of the subwoofer so it matches that of the other speakers in your configuration.

2 LOW FREQ.TEST

≥TEST TONE………OFF

OUTPUT…MAIN L/R FREQ.………………88Hz

■About the test tone

Digital generator

(wide band noise produced)

Noise

FREQ.

Band pass filter

35 Hz – 250 Hz

1 Tap or to set “TEST TONE” to “ON”. Cautions

•“ON” cannot be selected when the headphones are being used.

•Setting turns to “OFF” if the headphones are connected during testing.

•While the test tone is being output, the source sound cannot be output.

2 Adjust the volume with VOL +/– so you can hear the tone.

Cautions

•Do not turn up the volume too high.

•If no test tone is heard, turn down the volume, set this unit in the standby mode and make sure all the necessary connections are correct.

3 Tap to go to “OUTPUT” and tap or to select the speaker you want to compare with the subwoofer.

If “SWFR” is selected, the test tone above 90 Hz will not be output from the subwoofer. The test tone will not necessarily be output from the selected speakers. The output mode of the test tone depends on the settings of “1 SPEAKER SET” on the SET MENU.

4 Tap to go to “FREQ.” and tap or to select the frequency you want to use.

Set the center frequency (35 – 250 Hz or “35-250Hz”) to check that the subwoofer level matches that of the other speakers.

5 Adjust the volume of the subwoofer with the controls on the subwoofer so it matches that of the speaker you are comparing it to.

•The test tone is produced by the tone generator.

The tone generator produces a narrow-band noise centered on a specified frequency by the band pass filter.

•You can change this center frequency from 35 Hz through 250 Hz in one-sixth octave steps.

•You can use the test tone not only for adjusting the subwoofer level, but also for checking the low-frequency characteristics of your listening room. Low-frequency sounds are especially affected by the listener’s position, speaker placement, subwoofer polarity and other conditions.

Center freq.

E-60

Contents

Page Page FCC INFORMATION (for US customers only) For RAV-2000Z1 COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Electronics Corp Address: 6660 Orangethorpe Ave Buena Park, CA90620 Page Contents E-2 Introduction ■Built-in 8-channelpower amplifier ■Digital Sound Fields (DSP) ■CINEMA-DSP:Dolby Digital + DSP and DTS + DSP ■Virtual CINEMA DSP and SILENT CINEMA DSP ■Various decoders to support the newest sound effect technology ■Various input and output jacks ■Intelligent remote control 4567 89 0 q w e r tyu i o p a s E-6 ■Opening and closing the front panel door ■Display on the touch screen ■Installing batteries in the remote control ■ About changing batteries ■Using the remote control ■Turning on the display ■Using the backlight ■Activating modes ■Using touch screen buttons ■Using the left/right buttons 789 0 q w e r t y ui E-11 0 q w E-12 Preparations ■8-speakerconfiguration –full CINEMA-DSP– ■6-speakerconfiguration –Hi-FiDSP– ■5-speakerconfiguration –standard5.1 channel– ■ 4-speakerconfiguration –minimumrequirement– ■Speaker configurations and speaker mode ■Placing the main speakers ■Placing the center speaker ■Placing the front effect, rear and rear center speakers ■When you use a projection screen ■Placing the subwoofers E-18 ■Connecting a CD recorder ■Connecting a CD player ■Connecting an MD recorder/tape deck ■Connecting a turntable ■Connecting the indoor FM antenna Connecting the AM loop antenna ■About the video jacks ■Connecting a DVD player ■Connecting a digital TV/TV ■Connecting a cable TV tuner ■Connecting a satellite tuner ■Connecting a VCR ■Connecting an LD player ■Connecting a video monitor ■Connecting the SPEAKERS terminals ■Connecting a front subwoofer ■Connecting a rear subwoofer ■Impedance selector switch ■Connecting external amplifiers ■Connecting an external decoder ■Connecting a game console ■Connecting the AC power cord ■AC OUTLETS P10 MOVIE THEATER E-33 ■Summary of SPEAKER SET items 1A through 1G ■Mode setting ■1A CENTER SP (center speaker mode) ■1B MAIN SP (main speaker mode) ■1C REAR L/R SP (rear speaker mode) ■1D REAR CT SP (rear center speaker mode) ■1E LFE/BASS OUT (bass output mode) ■1F FRONT EFCT SP (front effect speaker mode) ■1G MAIN LEVEL ■Before you begin ■Display (on the remote control) to be used TEST DOLBY SUR LEFT TEST DSP MAIN Basic operations ■Item tabs ■Left/right buttons AUTO:DTS 6CH INPUT ■BGV (Back Ground Video) function ■To mute the sound ■When you have finished using this unit DVD ■Notes on the digital signal ■Notes on playing DTS-CD/LDs ■Notes on playing an LD source THEATER Spectacle ■Normal stereo reproduction STEREO DTS 3/2/LFE Dolby D 2/0 PCM 48kHz ■Playing the Dolby Digital EX or DTS ES software EX/ES AUTO:Disc ■ Selecting PRO LOGIC, PRO LOGIC or Neo: ■Virtual CINEMA DSP ■SILENT CINEMA DSP ■DTS 96/24 ■Automatic tuning FM or AM ■Manual tuning AM 1440 kHz Village Gate ■Automatically presetting stations (for FM stations) A-1:FM87.5 MHz ■Manually presetting stations C :AM 1440 kHz C-3:AM1440 kHz ■ Exchanging preset stations Tuning in to a preset station EDIT ■Special considerations when recording DTS Advanced operation E-58 SET MENU 1/5 E-59 ■About the test tone 3 HP TONE CTRL 4 CENTER GEQ 5 REAR CT GEQ E-61 ■6A L, C, R EQ (main L/center/main R equalizer) ■6B FRNT EFCT EQ (front effect equalizer) ■6C REAR L/R EQ (rear L/R equalizer) ■6D REAR CT EQ (rear center equalizer) ■8A <1> to <4> COAXIAL INPUT jacks ■8B <5> and <6> OPTICAL OUTPUT jacks ■8C <7> to <12> OPTICAL INPUT jacks ■8D [A] to [C] COMPONENT VIDEO INPUT jacks 9 INPUT MODE E-65 12 DYNAMIC RANGE 13 SP DELAY E-66 ■Setting by “msec” ■Setting by “meters” ■Setting by “feet” ■ DIMMER ■OSD SHIFT (OSD off-setposition) ■BLUE BACK ■ ZONE2 OUT ■ CTRL IN ■18A CENTER to (direction of the center channel signals) ■18B SWFR to (direction of the signals input into the subwoofer) ■ Via the Home menu ■ Via the Device menu ■Switching to another component without affecting the active component E-72 ■Defining brands by selecting E-74 ■Defining brands by searching E-76 ■Switching to another mode ■Hiding the Mode menu ■Redefining brands by selecting ■Redefining brands by searching ■Learning control panel buttons ■Learning device actions ■Learning direct-accessand left/right buttons ■Labeling a button ■Labeling a component ■Adding a component ■Moving a component, macro group or timer group ■Deleting a button or button action ■Deleting a device action ■Deleting a component, macro group or timer group ■Restoring buttons and button actions ■Restoring device actions ■Restoring components, macro groups or timer groups ■Recording macros ■Adding a component to a power group ■Recording extra commands ■Editing macros ■Organizing macros into groups ■Setting timers ■Editing timers ■Organizing timers into groups ■Functions and adjustments ■System requirements CENTER R SUR REAR CT L SUR FRONT ■ Setting the sleep timer SLEEP 120min 90min 60min ■A sample of system configuration and connections ■Special considerations when using DTS software E-93 Page Sound field programs ■Early reflections ■Reverberations ■Virtual sound sources ■Echo patterns E-98 ■ Europe Hall A ■ Europe Hall B ■ Europe Hall C ■U.S.A. Hall D ■Europe Hall E Page Page ■Table of program names for each input format ■DOLBY PRO LOGIC + DSP sound field effect ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital EX/DTS ES + DSP sound field effect ■Game ■Pop/Rock ■DJ ■Classical/Opera ■Pavilion ■To reset some of the parameters to the factory-setvalues ■To reset all of the parameters to the factory set values ■EFCT TRIM (Effect Trim) ■INIT. DLY (Initial Delay) ■ROOM SIZE/P. ROOM SIZE for the presence sound field ■LIVENESS ■P. INIT. DLY (Presence Initial Delay) ■S. INIT. DLY (Surround Initial Delay) ■S. DELAY (Surround Delay) ■S. ROOM SIZE (Surround Room Size) ■S. LIVENESS (Surround Liveness) ■RC INI. DLY (Rear Center Initial Delay) ■RC ROOM SIZE (Rear Center Room Size) ■REV. TIME (Reverberation Time) ■REV. DELAY (Reverberation Delay) ■REV. LEVEL (Reverberation Level) For 8ch Stereo ■CT LEVEL (Center Level) ■RL LEVEL (Rear Left Level) ■RC LEVEL (Rear Center Level) ■RR LEVEL (Rear Right Level) Appendix ■ General Page ■Tuner Page Page Page ■L, C, R preset value ■FRONT and REAR preset value ■ HIGH frequency ■ PEQ frequency Page ■ Audio Section ■ Video Section ■ FM Section ■ AM Section ■Remote Control