Yamaha pmn ■Learning control panel buttons, E-79

REMOTE CONTROL FEATURES

Learning commands

10 to 20cm

(4 to 8 inches)

You can program the remote control commands by transmitting IR signals from your existing remote controls to the remote control’s learning eye. To do this, place the remote control and the component’s remote control on a flat surface, 10 to 20 cm (4 to 8 inches) apart.

The following buttons can be programmed:

•Control panel buttons.

•Device actions.

•Direct-access buttons and left/right buttons.

You cannot program Home menu buttons directly. You must program components via the Device menu.

The remote control also offers empty control panel buttons that you can program and label as existing buttons. They are visible only in the Learn and Label mode and appear with or without labels (intended for a specific function). You will also see previously deleted buttons: you can restore them by reprogramming them or you can reuse them for other commands.

■Learning control panel buttons

1 Navigate to the control panel buttons you want to program.

2 Switch to the Learn mode via at the bottom of the touch screen.

Additional empty buttons appear: they can be programmed and labeled as existing buttons.

3 Point the component’s original remote control at the remote control’s learning eye. 4 Tap the control panel button you want to program.

The button starts flashing.

5 Press and hold the corresponding button on your component’s original remote control.

If the remote control has learned the command successfully, “OK” flashes on the upper center of the touch screen. You can release the button you’re holding.

If the remote control has not learned the command successfully, you will hear a short buzz and “FAIL” will appear on the remote control icon.

6 Program all other buttons you want and relabel them if necessary.

7 Return to the Use mode via .

E-79

OPERATION	ADVANCED

English

Contents

Page Page FCC INFORMATION (for US customers only) For RAV-2000Z1 COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Electronics Corp Address: 6660 Orangethorpe Ave Buena Park, CA90620 Page Contents E-2 Introduction ■Built-in 8-channelpower amplifier ■Digital Sound Fields (DSP) ■CINEMA-DSP:Dolby Digital + DSP and DTS + DSP ■Virtual CINEMA DSP and SILENT CINEMA DSP ■Various decoders to support the newest sound effect technology ■Various input and output jacks ■Intelligent remote control 4567 89 0 q w e r tyu i o p a s E-6 ■Opening and closing the front panel door ■Display on the touch screen ■Installing batteries in the remote control ■ About changing batteries ■Using the remote control ■Turning on the display ■Using the backlight ■Activating modes ■Using touch screen buttons ■Using the left/right buttons 789 0 q w e r t y ui E-11 0 q w E-12 Preparations ■8-speakerconfiguration –full CINEMA-DSP– ■6-speakerconfiguration –Hi-FiDSP– ■5-speakerconfiguration –standard5.1 channel– ■ 4-speakerconfiguration –minimumrequirement– ■Speaker configurations and speaker mode ■Placing the main speakers ■Placing the center speaker ■Placing the front effect, rear and rear center speakers ■When you use a projection screen ■Placing the subwoofers E-18 ■Connecting a CD recorder ■Connecting a CD player ■Connecting an MD recorder/tape deck ■Connecting a turntable ■Connecting the indoor FM antenna Connecting the AM loop antenna ■About the video jacks ■Connecting a DVD player ■Connecting a digital TV/TV ■Connecting a cable TV tuner ■Connecting a satellite tuner ■Connecting a VCR ■Connecting an LD player ■Connecting a video monitor ■Connecting the SPEAKERS terminals ■Connecting a front subwoofer ■Connecting a rear subwoofer ■Impedance selector switch ■Connecting external amplifiers ■Connecting an external decoder ■Connecting a game console ■Connecting the AC power cord ■AC OUTLETS P10 MOVIE THEATER E-33 ■Summary of SPEAKER SET items 1A through 1G ■Mode setting ■1A CENTER SP (center speaker mode) ■1B MAIN SP (main speaker mode) ■1C REAR L/R SP (rear speaker mode) ■1D REAR CT SP (rear center speaker mode) ■1E LFE/BASS OUT (bass output mode) ■1F FRONT EFCT SP (front effect speaker mode) ■1G MAIN LEVEL ■Before you begin ■Display (on the remote control) to be used TEST DOLBY SUR LEFT TEST DSP MAIN Basic operations ■Item tabs ■Left/right buttons AUTO:DTS 6CH INPUT ■BGV (Back Ground Video) function ■To mute the sound ■When you have finished using this unit DVD ■Notes on the digital signal ■Notes on playing DTS-CD/LDs ■Notes on playing an LD source THEATER Spectacle ■Normal stereo reproduction STEREO DTS 3/2/LFE Dolby D 2/0 PCM 48kHz ■Playing the Dolby Digital EX or DTS ES software EX/ES AUTO:Disc ■ Selecting PRO LOGIC, PRO LOGIC or Neo: ■Virtual CINEMA DSP ■SILENT CINEMA DSP ■DTS 96/24 ■Automatic tuning FM or AM ■Manual tuning AM 1440 kHz Village Gate ■Automatically presetting stations (for FM stations) A-1:FM87.5 MHz ■Manually presetting stations C :AM 1440 kHz C-3:AM1440 kHz ■ Exchanging preset stations Tuning in to a preset station EDIT ■Special considerations when recording DTS Advanced operation E-58 SET MENU 1/5 E-59 ■About the test tone 3 HP TONE CTRL 4 CENTER GEQ 5 REAR CT GEQ E-61 ■6A L, C, R EQ (main L/center/main R equalizer) ■6B FRNT EFCT EQ (front effect equalizer) ■6C REAR L/R EQ (rear L/R equalizer) ■6D REAR CT EQ (rear center equalizer) ■8A <1> to <4> COAXIAL INPUT jacks ■8B <5> and <6> OPTICAL OUTPUT jacks ■8C <7> to <12> OPTICAL INPUT jacks ■8D [A] to [C] COMPONENT VIDEO INPUT jacks 9 INPUT MODE E-65 12 DYNAMIC RANGE 13 SP DELAY E-66 ■Setting by “msec” ■Setting by “meters” ■Setting by “feet” ■ DIMMER ■OSD SHIFT (OSD off-setposition) ■BLUE BACK ■ ZONE2 OUT ■ CTRL IN ■18A CENTER to (direction of the center channel signals) ■18B SWFR to (direction of the signals input into the subwoofer) ■ Via the Home menu ■ Via the Device menu ■Switching to another component without affecting the active component E-72 ■Defining brands by selecting E-74 ■Defining brands by searching E-76 ■Switching to another mode ■Hiding the Mode menu ■Redefining brands by selecting ■Redefining brands by searching ■Learning control panel buttons ■Learning device actions ■Learning direct-accessand left/right buttons ■Labeling a button ■Labeling a component ■Adding a component ■Moving a component, macro group or timer group ■Deleting a button or button action ■Deleting a device action ■Deleting a component, macro group or timer group ■Restoring buttons and button actions ■Restoring device actions ■Restoring components, macro groups or timer groups ■Recording macros ■Adding a component to a power group ■Recording extra commands ■Editing macros ■Organizing macros into groups ■Setting timers ■Editing timers ■Organizing timers into groups ■Functions and adjustments ■System requirements CENTER R SUR REAR CT L SUR FRONT ■ Setting the sleep timer SLEEP 120min 90min 60min ■A sample of system configuration and connections ■Special considerations when using DTS software E-93 Page Sound field programs ■Early reflections ■Reverberations ■Virtual sound sources ■Echo patterns E-98 ■ Europe Hall A ■ Europe Hall B ■ Europe Hall C ■U.S.A. Hall D ■Europe Hall E Page Page ■Table of program names for each input format ■DOLBY PRO LOGIC + DSP sound field effect ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital EX/DTS ES + DSP sound field effect ■Game ■Pop/Rock ■DJ ■Classical/Opera ■Pavilion ■To reset some of the parameters to the factory-setvalues ■To reset all of the parameters to the factory set values ■EFCT TRIM (Effect Trim) ■INIT. DLY (Initial Delay) ■ROOM SIZE/P. ROOM SIZE for the presence sound field ■LIVENESS ■P. INIT. DLY (Presence Initial Delay) ■S. INIT. DLY (Surround Initial Delay) ■S. DELAY (Surround Delay) ■S. ROOM SIZE (Surround Room Size) ■S. LIVENESS (Surround Liveness) ■RC INI. DLY (Rear Center Initial Delay) ■RC ROOM SIZE (Rear Center Room Size) ■REV. TIME (Reverberation Time) ■REV. DELAY (Reverberation Delay) ■REV. LEVEL (Reverberation Level) For 8ch Stereo ■CT LEVEL (Center Level) ■RL LEVEL (Rear Left Level) ■RC LEVEL (Rear Center Level) ■RR LEVEL (Rear Right Level) Appendix ■ General Page ■Tuner Page Page Page ■L, C, R preset value ■FRONT and REAR preset value ■ HIGH frequency ■ PEQ frequency Page ■ Audio Section ■ Video Section ■ FM Section ■ AM Section ■Remote Control