SAFETY INSTRUCTIONS

1Read Instructions — All the safety and operating instructions should be read before the unit is operated.

2Retain Instructions — The safety and operating instructions should be retained for future reference.

3Heed Warnings — All warnings on the unit and in the operating instructions should be adhered to.

4Follow Instructions — All operating and other instructions should be followed.

5Water and Moisture — The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.

6Carts and Stands — The unit should be used only with a cart or stand that is recommended by the manufacturer.

6A An unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn.

7Wall or Ceiling Mounting — The unit should be mounted to a wall or ceiling only as recommended by the manufacturer.

8Ventilation — The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9Heat — The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat.

10Power Sources — The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit.

11Power-Cord Protection — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.

12Cleaning — The unit should be cleaned only as recommended by the manufacturer.

13Nonuse Periods — The power cord of the unit should be unplugged from the outlet when left unused for a long period of time.

14Object and Liquid Entry — Care should be taken so that objects do not fall into and liquids are not spilled into the inside of unit.

15Damage Requiring Service — The unit should be serviced by qualified service personnel when:

A.The power-supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the unit; or

C.The unit has been exposed to rain; or

D.The unit does not appear to operate normally or exhibits a marked change in performance; or

E.The unit has been dropped, or the enclosure damaged.

16Servicing — The user should not attempt service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel.

17Power Lines — An outdoor antenna should be located away from power lines.

18Grounding or Polarization — Precautions should be taken so that the grounding or polarization is not defeated.

19Outdoor Antenna Grounding — If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST

ANTENNA

 

LEAD IN

 

WIRE

GROUND

 

CLAMP

 

 

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC

 

SERVICE

 

EQUIPMENT

 

 

GROUNDING CONDUCTORS

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

 

POWER SERIVCE GROUNDING

 

ELECTRODE SYSTEM

 

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

 

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.