Yamaha RX-V2090 Features, OPEN/CLOSE THE CONTROL DOOR

Features

• Seven Speaker Configuration

Main: 100 W + 100 W (8Ω) RMS Output Power,

0.015% THD, 20-20,000 Hz

120 W + 120 W (6Ω) RMS Output Power,

0.04% THD, 20-20,000 Hz (USA Model Only)

Center: 100 W (8Ω) RMS Output Power,

0.015% THD, 1 kHz

Front: 35 W + 35 W (8Ω) RMS Output Power,

0.08% THD, 1 kHz

Rear: 35 W + 35 W (8Ω) RMS Output Power,

0.08% THD, 1 kHz

•Multi-Room Capability

Multi-Room and Multi-Source with two Remote Control Units

•Digital Sound Field Processor

10 Programs including “Cinema DSP” 70mm Movie Theater

•5 Channel Discrete Input for Dolby Surround Digital AC-3

•Automatic Input Balance Control for Dolby Surround

•Test Tone Generator for Easier Speaker Output Balance Adjustment

•3 Center Channel Modes (NORMAL/WIDE/PHANTOM)

•40-Station Random Access Preset Tuning

•Automatic Preset Tuning (FM only)

•Preset Station Shifting Capability (Preset Editing)

•IF Count Direct PLL Synthesizer Tuning System

•Video Signal Input/Output Capability

•SLEEP Timer

•Remote Control Capability

•Program and status messages superimposed on connected video monitor

OPEN/CLOSE THE CONTROL DOOR

To open the door

To close the door

When it is not necessary to operate controls inside the control door, close the door.

5

Contents

Natural Sound Stereo Receiver OWNER’S MANUAL Contents SAFETY INSTRUCTIONS CAUTION: READ THIS BEFORE OPERATING YOUR UNIT FCC INFORMATION We Want You Listening For A Lifetime SUPPLIED ACCESSORIES Features OPEN/CLOSE THE CONTROL DOOR PROFILE OF THIS UNIT Digital Sound Field Processing Dolby Pro Logic Surround Dolby Pro Logic Surround + DSP Directional Enhancement Circuit + DSP SPEAKER SETUP FOR THIS UNIT SPEAKERS TO BE USED SPEAKER CONFIGURATION Seven-SpeakerConfiguration Five-SpeakerConfiguration SPEAKER PLACEMENT CONNECTIONS CONNECTIONS WITH OTHER COMPONENTS CONNECTING SPEAKERS ABOUT THE ACCESSORY TERMINALS 1LOW PASS terminal 2CENTER OUTPUT terminal 3FRONT OUTPUT terminals 4REAR OUTPUT terminals 5MAINÊ CH — MAINÊ IN terminals 6MAINÊ CH — PREÊ OUT terminals 7MAIN LEVEL switch 8ROOM 2 OUT — AUDIO PRE OUT, VIDEO OUT terminals 9REMOTE CONTROL — IN, OUT terminals CONNECTING SÊ VIDEO TERMINALS ON SCREEN DISPLAY CONNECTING TO VIDEO AUX TERMINALS (FRONT PANEL) CONNECTING TO ROOM 2 EQUIPMENT Using the Remote Transmitters ANTENNA CONNECTIONS ADJUSTMENT BEFORE OPERATION SPEAKER BALANCE ADJUSTMENT Seven and five speaker configuration Six and Four speaker configuration Page BASIC OPERATIONS To play a source To record a source to tape (or dub from tape to tape) Selecting the SPEAKERS system Using the TONE BYPASS switch Adjusting the BALANCE control Adjusting the BASS and TREBLE controls Using the BASS EXTENSION switch TUNING OPERATIONS AUTOMATIC TUNING MANUAL TUNING PRESET TUNING Manual Preset Tuning To program stations To recall a preset station Automatic Preset Tuning Exchanging Preset Stations USING THE DIGITAL SOUND FIELD PROCESSOR (DSP) Description of Each Sound Field Program Description of Dolby Pro Logic Surround To play a source with the digital sound field processor Dolby Surround AC-3 Adjustment of the FRONT LEVEL Adjustment of the CENTER LEVEL Adjustment of the REAR LEVEL Adjustment of DELAY TIME SETTING THE SLEEP TIMER To set the SLEEP time To cancel the selected SLEEP time REMOTE CONTROL TRANSMITTER Battery installation Battery replacement STANDBY mode (Singapore model only) For Control of This Unit For Other Component Control REMOTE CONTROL “LEARNING” FUNCTION To learn a new function To clear a learned function To clear all learned functions Troubleshooting guide TROUBLESHOOTING SPECIFICATIONS