Using the Remote Control

Remote control sensor

Within approximately 6 m (20 feet)

GETTING STARTED

	The remote control transmits a directional infrared beam. Be
	sure to aim the remote control directly at the infrared sensor
	during operation. When the sensor is covered or there is a	INTRODUCTION
	large object between the remote control and the sensor, the	INTRODUCTION
	large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a fluorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting.

Notes

•Handle the remote control with care.

•Do not spill water, tea or other liquids on the remote control.

•Do not drop the remote control.

•Do not leave or store the remote control in the following conditions:

–high humidity or temperature such as near a heater, stove or bath;

–dusty places; or

–extremely low temperature.

English

Page 5

Image 5

Yamaha RX-V496RDS owner manual Using the Remote Control

Contents

RX-V496RDS Special Instructions for U.K. Model For U.K. customers Featurescontents Battery Replacement Checking the Package ContentsGetting Started Control Using the Remote Control Front Panel Controls and Functions PRESET/TUNING, Edit PRESET/TUNINGTuning Mode AUTO/MAN’L Mono PTY Seek Mode Display Remote Control Speakers to Be Used Speaker SetupSpeaker Placement Connections Before Connecting Components Outdoor FM antenna Connecting the AntennasIndoor FM antenna included AM loop antenna included Connecting the AM loop antennaOutdoor AM antenna Ground GND terminal Phono terminals Connecting an Audio Component Audio signal terminals Connecting a Video ComponentVideo signal terminals Digital audio signal terminals Video AUX terminals on the front panel Video terminals Main speaker terminals Connecting SpeakersRear speaker terminals Center speaker terminal Speaker cables Connecting to the Main Speakers terminalsConnecting to the Rear and Center Speakers terminals AC Outlets Switched Impedance Selector SwitchConnecting the Power Supply Cords Before You Start Adjusting Using the Test Tone Adjusting the Speaker BalanceTurn up the volume Set BASS, Treble and Balance to the 0 position Press Test Test OFF appears on the display and the test tone stops When the adjustment is complete, press Test To select a tape or an MD source Playing a SourcePress Speakers a or B To select the main BGV background video function When you have finished using this unitTo mute the sound Auto Switching the input modeDTS Analog Encoded with DTS Digital Sound Field Processor DSP Effect On the remote controlSelecting a DSP Program Off the effect speakers Sound Field Program Theater Program Subprogram Features MovieDgtl Spectacle Dgtl Adventure Dolby Digital or DTS + 3 digital sound fields For Hi-Fi audio sourcesDolby Pro Logic + 2 digital sound fields Automatic Tuning TuningManual Tuning Press PRESET/TUNING Edit to turn z off When automatic preset tuning is completed Automatic preset tuning optionsStations only Hold down Memory for about three seconds To Recall a Preset Station Manual Preset Tuning Example If you want to exchange preset station E1 with A5 Exchanging Preset StationsRecall preset station E1 Hold down PRESET/TUNING Edit for about three second Description of RDS Data Changing the RDS ModeReceiving RDS Stations Program types in the PTY mode To cancel this functionPress PTY Seek Mode to set the unit in the PTY Seek mode PTY Seek Function EON Function Make sure that the EON indicator lights up on the display Select the source you want to record Recording a Source on TAPE, MD or Video Cassette SET Menu Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputCenter SP Rear SP Main SP Bass OUT Main LVL D. LFE Center SP Description of Each Item MIN Range Adjusting the dynamic rangeMAX Last Cntr Delay Adjusting the delay of the center soundAuto Delay Time Delay Time and Speaker Output LevelsSound Output Level of the Center Subwoofer Adjusting Method Setting the Sleep Timer Sleep TimerCanceling the Selected Sleep Timer Example To control Yamaha CD player Preset Remote ControlControlling the Components Connected to This Unit Display MD Description of Each ModeTAPE/MD Mode Display CD Mode DVD Menu Mode DVD/LD Mode TV Mode VCR ModeCBL/SAT Mode To use a second and third VCR Setup codesAdvanced Information Enter the code number Returning to the factory-set codes General TroubleshootingSymptom Cause Remedy Be heard Tuner Others Remote controlWhen playing back a source encoded with DTS Specifications Cinema DSP Cinema DSP Glossary Video components DVD/LD player, VCR and TV Index BSR SEG VCR CableSatellite Tuner CD Player DVD PlayerLD Player Tape Deck MD Recorder V502870-2 Amptuner TAPE/MD DVD/LD Quick Reference Card VCR Stop DVD Menu VCR CBL/SAT