Connecting audio and video components

Determine the connection types depending on the jacks available on this unit and your external components. The symbols in the following table correspond with the symbols described in “Cables used for connections” (page 12).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HDMI

IN 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN 3

IN

OUT AUX 1 TV AUX 2

AUX 1

TV

 

 

 

 

 

 

 

IN 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

 

AUDIO IN

 

 

DIGITAL IN

 

IR IN

 

RS-232C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

AUDIO IN

 

DIGITAL IN

VIDEO IN/OUT

AUDIO IN

DIGITAL IN

HDMI IN

jacks

jacks

jacks

jacks

External component
Signal type
Jacks to use
Cable to
Input selection
On external component
On this unit
use
key

 

 

 

 

 

 

 

 

 

 

 

 

TV

Video

Composite video input

VIDEO OUT

 

 

 

 

 

 

 

 

 

Audio

Analog audio output

AUDIO IN (TV)

 

TV

 

 

 

 

 

 

External component

Audio/video

HDMI output

HDMI IN 1-4

 

HDMI1-4

with HDMI output

 

 

 

 

 

 

 

 

 

 

 

External component

Audio

Coaxial digital output

DIGITAL IN (AUX 2)

 

AUX2

with component video

 

 

 

 

 

output

 

 

 

 

 

Video

Component video output

VIDEO IN (COMPONENT)

 

 

 

 

 

 

 

 

 

 

 

External component

Audio

Optical digital output

DIGITAL IN (AUX 1)

 

AUX1

with composite video

 

 

 

 

 

output

 

 

 

 

 

 

Analog audio output

AUDIO IN (AUX 1)

 

 

 

 

 

 

 

 

 

 

 

 

 

Video

Composite video output

VIDEO IN (VIDEO)

 

 

 

 

 

 

 

 

y

Video signals input from the VIDEO IN (VIDEO) jack can be output not only to the VIDEO OUT jack but also the HDMI OUT jack. Video signals input from the VIDEO IN (COMPONENT) jacks are output to the HDMI OUT jack.

Connecting a subwoofer

Wireline connection

 

 

 

Wireless connection

Connect the monaural input jack on your subwoofer to the

You can make a wireless connection of your subwoofer by using the

SUBWOOFER jack on this unit.

 

 

Yamaha wireless subwoofer kit (SWK-W10). About SWK-W10,

SUB

 

 

 

refer to “Safety and Accessory Information” (separate booklet).

 

 

 

 

WOOFER

 

 

 

See also: “WIRELESS SETUP” (page 39)

 

SIRIUS

 

SYSTEM

 

 

 

 

 

 

CONNECTOR

 

OUT AUX 1 TV AUX 2

AUX 1

TV

 

 

AUDIO IN

DIGITAL IN

IR IN

RS-232C

 

 

 

 

 

Subwoofer

 

 

 

 

SWK-W10

Monaural input

System connector

 

 

 

 

 

y

 

 

 

 

• For proper transmission, you need to set the group IDs of this unit and

 

 

 

 

SWK-W10 to the same value. For the Group ID settings, refer to “Group

 

 

 

 

ID” (page 39) and “Safety and Accessory Information (separate booklet)”.

y

 

 

 

Note

• If the subwoofer is connected by using a system type connection, changing

 

the power mode of this unit controls the power mode of the subwoofer

• Be sure to use the product only in the country in where it was purchased.

(Yamaha subwoofer).

 

 

 

 

PREPARATION INTRODUCTION

FEATURES PLAYBACK

SETTINGS

APPENDIX

13 En