Parts List, Description | Zebra Technologies R402 instruction

Parts List

	ITEM	DESCRIPTION

	1	Latch Assembly	105910-052

	2	Feed Switch/Sensor Assy (set of 3)	105910-128

	3	Upper Cover Support (set of 3)	105910-066

	4	Print Head Assy - 4” TLP	105910-053
	4	Print Head Cable Assy.	105910-065
		Print Head Cable Assy.	105910-065

	5	Head Up Sensor	105910-129

	6	Gap/Blackline Sensor PCBA (set of 3)	105910-054

	7	Platen Kit (standard set of 3)	105910-055

	8	Front Bezel (standard set of 10)	105910-057
	8	Front Bezel, Dispenser (single)	105910-022
		Front Bezel, Dispenser (single)	105910-022

	10	Rubber Foot Kit (set of 24)	105910-007

	11	Main Control PCBA (RFID)	105910-133

	12	Bottom Frame Assy	105910-130

	13	Upper Cover Assy	105910-131

	14	Ribbon Out Sensor (set of 3)	105910-134

	15	Ribbon Carriage w/o printhead	105910-132

	Not	Motor (set of 2)	105910-051
	Shown	Power Supply, 100V-240V	105950-043
		Power Cord, U.S. 120V IEC320C13 (set of 5)	105950-014
		PCBA, RFID Reader	105903-135
		PCBA, Antenna, Type 2	105950-136
		Ribbon Core, 4” (set of 50)	105903-053
		Accessory, Media Adapter Plates	810059-001

	Manuals	User’s Manual, R402	980389-001
	Manuals	ZPL II Programmer’s Manual	46530L
		ZPL II Programmer’s Manual	46530L

Image 46

Zebra Technologies R402 manual Parts List, Description

Contents

R402 Users GuidePage Proprietary Statement Page Contents Operation & Options Appendix 980389-001 Rev. a Introduction Hello What’s in the Box? Inspecting the Printer Opening the printer Inspecting the Printer Closing the printer Reporting Damage Getting Started Modes of Printing Attaching Power Supply Loading Roll Media Placing the Roll in the Media Compartment Adjusting the Guides Using the Optional Media Adapter Plates Install the Take-Up Core Install the Ribbon Supply RollLoading Ribbon Attach and Tighten the Ribbon Auto Calibration Feed Button Power SwitchOperator Controls Status Light Printing a Test Label Parallel Interface Requirements Hooking Up the Printer and ComputerInterface Cable Requirements Adjusting the Print Speed Adjusting the Print WidthAdjusting the Print Darkness Communicating with the Printer Operation & Options Thermal Printing Adding a New Transfer Ribbon Replacing SuppliesReplacing a Partially Used Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Rfid Guidelines Supported Transponders Texas Instruments Tag-it Transponders Philips ICode Transponders Philips ICode Blocks Inside Technologies Picotag Transponders Inside Technologies Picotag 2K ISO-15693 Transponders ZPL II Commands for Rfid WT Write Tag RT Read Tag RT Read Tag RS Rfid Setup RI Rfid Get Tag Unique ID Sample of Rfid Programming WT6FDZebraFS FO100,100A0n,60FN0FS Page Cleaning MaintenanceLubrication Parts List DescriptionPage Replacing the Print Head Removal Cleaning the Print Head Page Printer is not receiving power TroubleshootingResolutions Printer is on and in an idle state Printer is receiving data Printer has failed its power on self test PostThere is a shortage of memory Either the media or ribbon is out Print head is over temperature Print head is under temperatureFlash memory is not programmed No print on the label Print Quality ProblemsRibbon sensor settings did not print Printed image does not look right Label format was sent to, but not recognized by, the printer Void messages are printed across media Rfid SymptomsRfid tags generally not programmed Nothing is printed Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Resetting the Factory Default Values Communications Diagnostics Power Off Mode Communications Diagnostics Mode Feed Button Modes Physical Specifications Appendix Media Specifications Font/Code Specifications Options Parallel Interface Technical Information Page Index Cable calibration Quality problems Voltage Write tag command Page