Appendix, Physical Specifications | Zebra Technologies R402 instruction

Appendix

All specifications are subject to change without notice.

Physical Specifications

Size

Weight

7.8inches wide / 6.8 inches tall / 9.4 inches long (depth) 200 mm wide / 173 mm tall / 240 mm long (depth)

3.6 pounds / 1.6 kilograms

Environmental Guidelines

Operating temp.	40 to 104 degrees Fahrenheit / 5 to 40 degrees Celsius

Operating humidity	10 to 90 percent non-condensing

Storage temp.	-40 to 140 degrees Fahrenheit / -40 to 60 degrees Celsius

Storage humidity	5 to 90 percent non-condensing

Electrical	Autoranging external power supply
	Input: 100-240VAC; 50-60 Hz
	Output: 20VDC; 2.5A

Printing Specifications

	Print Density	203 dots per inch / 8 dots per millimeter

	Print Speed	2 inches / 51 millimeters per second
		3 inches / 76 millimeters per second
		4 inches / 102 millimeters per second

	Print Width	1.0 to 4.09 inches / 25.4 to 104 millimeters

	Print Length	0.005 to 22 inches / 0.125 to 559 millimeters
		with standard memory

	Registration	Horizontal: +/- 0.0591 inches (1.5 millimeters)
	Tolerance	Vertical: +/- 0.0393 inches (1.0 millimeters)

	FLASH Memory	768K
	(user available)

	DRAM Memory	1 MB
	(user available)

Image 61

Zebra Technologies R402 manual Appendix, Physical Specifications

Contents

Users Guide R402Page Proprietary Statement Page Contents Operation & Options Appendix 980389-001 Rev. a Hello Introduction What’s in the Box? Opening the printer Inspecting the Printer Inspecting the Printer Closing the printer Reporting Damage Modes of Printing Getting Started Attaching Power Supply Placing the Roll in the Media Compartment Loading Roll Media Adjusting the Guides Using the Optional Media Adapter Plates Install the Take-Up Core Install the Ribbon Supply RollLoading Ribbon Attach and Tighten the Ribbon Auto Calibration Operator Controls Power SwitchFeed Button Status Light Printing a Test Label Parallel Interface Requirements Hooking Up the Printer and ComputerInterface Cable Requirements Adjusting the Print Darkness Adjusting the Print WidthAdjusting the Print Speed Communicating with the Printer Thermal Printing Operation & Options Adding a New Transfer Ribbon Replacing SuppliesReplacing a Partially Used Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Rfid Guidelines Supported Transponders Texas Instruments Tag-it Transponders Philips ICode Blocks Philips ICode Transponders Inside Technologies Picotag 2K Inside Technologies Picotag Transponders ISO-15693 Transponders WT Write Tag ZPL II Commands for Rfid RT Read Tag RT Read Tag RS Rfid Setup RI Rfid Get Tag Unique ID Sample of Rfid Programming WT6FDZebraFS FO100,100A0n,60FN0FS Page Cleaning MaintenanceLubrication Description Parts ListPage Removal Replacing the Print Head Cleaning the Print Head Page Resolutions TroubleshootingPrinter is not receiving power Printer is on and in an idle state There is a shortage of memory Printer has failed its power on self test PostPrinter is receiving data Either the media or ribbon is out Print head is over temperature Print head is under temperatureFlash memory is not programmed Ribbon sensor settings did not print Print Quality ProblemsNo print on the label Printed image does not look right Label format was sent to, but not recognized by, the printer Rfid tags generally not programmed Rfid SymptomsVoid messages are printed across media Nothing is printed Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Communications Diagnostics Resetting the Factory Default Values Feed Button Modes Power Off Mode Communications Diagnostics Mode Appendix Physical Specifications Media Specifications Font/Code Specifications Options Parallel Interface Technical Information Page Cable calibration Index Quality problems Voltage Write tag command Page