Husqvarna 240, 235 manuel dutilisation Tensioning the chain, Lubricating cutting equipment

Page 12

GENERAL SAFETY PRECAUTIONS

File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced. (8)

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off

! the bar and cause serious or even fatal injury.

WARNING! Always wear approved

! protective gloves. Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand. (9)

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can. (10)

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar. (11)

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar. (12)

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

! equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

•All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

•The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

•Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

•Check that the oil channel in the bar is not obstructed. Clean if necessary.

•Check that the groove in the edge of the bar is clean. Clean if necessary.

•Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

12 – English

5451546-93 Rev.4 2008-04-16

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 235 5451546-93 Rev.4 OFF Half Full 49 a 5451546-93 Rev.4 Symbols on the machine Thank you for using a Husqvarna productIntroduction Dear customerWhat is what on the chain saw? Contents General Safety Precautions Before using a new chain sawFor Canada Machine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardCutting equipment Sharpening your chain and adjusting depth gauge setting General rulesCutting equipment designed to reduce kickback BarTensioning the chain Lubricating cutting equipmentGeneral Safety Precautions / Assembly Happen when the chain touches the operatorFitting the bar and chain Chain drive sprocketFuel safety Fuel HandlingFuel FuelingFuel Handling / Starting and Stopping Starting and stoppingBasic safety rules Working TechniquesBefore use General working instructionsBasic cutting technique Tree felling techniqueFreeing a tree that has fallen badly Working Techniques / Maintenance How to avoid kickbackCarburetor adjustment GeneralMaintenance MufflerAir filter Spark plugMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataRecommended cutting equipment for Canada Bar ChainType Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsSymboles sur la machine Cher clientNous vous remercions dutiliser un produit Husqvarna Quels sont les composants de la tronçonneuse? SommaireMesures à prendre avant de mettre en usage une Instructions Générales DE Sécurité Utilisez toujours votre bon sens Équipement de sécurité de la machineFrein de chaîne avec arceau protecteur AVERTISSEMENT! La plupart desBlocage de l’accélération Capteur de chaîneProtection de la main droite Système anti-vibrationsÉquipement de coupe Règles élémentairesÉquipement de coupe anti-rebond Affûtage et réglage de l’épaisseur du copeau de la chaîneTension de la chaîne Lubrification de l’équipement de coupeInstructions Générales DE Sécurité / Montaje Montage du guide-chaîne et de la chaîneManipulation DU Carburant CarburantRemplissage de carburant Sécurité carburant Transport et rangementRemisage prolongé Démarrage ET Arrêt Démarrage et arrêtTechniques DE Travail Avant chaque utilisationMéthodes de travail Règles élémentaires de sécuritéTechnique de base pour la coupe AVERTISSEMENT! N’utilisez jamais uneGénéralités TerminologieSolution à un abattage raté Techniques d’abattageMesures anti-rebond Qu’est-ce qu’un rebond?Entretien GénéralitésRéglage du carburateur FonctionnementSilencieux Filtre à airBougie Schéma d’entretien Entretien hebdomadaireTous lesCaractéristiques Techniques Caractéristiques techniquesÉquipement DE Coupe Recommandé Pour Canada Guide-chaîne ChaîneVOS Droits ET Obligations EN Garantie Précautions à prendre pour se protéger des rebonds Autres consignes de sécuritéAnsi B 175.1-2000 Annexe C AVERTISSEMENT! N’utilisez pas uneIntroducción Apreciado clienteSímbolos en la máquina ¿Qué es qué en la motosierra? Índice Instrucciones Generales DE Seguridad Medidas a tomar antes de utilizar una motosierra nuevaImportante Emplee siempre el sentido comúnEquipo de protección personal Equipo de seguridad de la máquinaFreno de cadena con protección contra reculadas ¡ATENCIÓN! La mayoría de losFiador del acelerador Captor de cadenaProtección de la mano derecha Sistema amortiguador de vibracionesEquipo de corte Reglas básicasEquipo de corte reductor de reculadas EspadaTensado de la cadena Lubricación del equipo de corteRepostaje de aceite para cadena de motosierra Instrucciones Generales DE Seguridad / Montaje Montaje de la espada y la cadenaManipulacion DEL Combustible CarburanteRepostaje Seguridad en el uso del combustibleManipulacion DEL Combustible / Arrenque Y Parada Arranque y paradaTécnica DE Trabajo Antes de utilizar la máquinaReglas básicas de seguridad Corte con velocidad de cadena alta, acelerando al máxTécnica básica de corte Técnica de talaTratamiento de una tala fallida Mantenimiento GeneralidadesAjuste del carburador Silenciador Filtro de aireBujía Programa de mantenimiento Datos Tecnicos Datos técnicosEspada Cadena Garantia DEL Sistema DE Control DE Emisiones SUS Derechos Y Obligaciones DE GarantiaPrecauciones DE Seguridad DE LA Norma Americana Precauciones de seguridad para usuarios de motosierrasPrecauciones de seguridad en reculadas Otras precauciones de seguridad5451546-93 2008-04-16

235, 240 specifications

The Husqvarna 235 and 240 chainsaws are compact, lightweight power tools designed for homeowners and occasional users seeking reliability and performance. Known for their ease of use and versatility, both models are ideal for tasks such as pruning, cutting firewood, and clearing small trees.

One of the main features of the Husqvarna 235 and 240 is their X-Torq engine technology. This innovation reduces fuel consumption by up to 20% while also cutting emissions by approximately 75%. This not only makes the chainsaws environmentally friendly but also saves users on fuel costs over time. The engine's design also enhances torque, providing ample power for cutting through wood efficiently.

Both models come equipped with an inertia-activated chain brake, enhancing safety by preventing unwanted chain movement in case of a kickback. The chain brake is a critical feature for novice users, promoting confidence while operating the chainsaw. This focus on safety extends to the easy-to-reach throttle lockout and combined choke/stop control, allowing for simpler starting procedures.

The Husqvarna 235 and 240 feature an adjustable oil pump, which enables users to control the oil flow to the chain according to their specific needs. This functionality not only prolongs the life of the chain and bar but also helps maintain cutting performance, ensuring smoother operation and reduced wear.

These chainsaws also have ergonomic designs, with comfortable handles that minimize vibrations and allow for prolonged use without fatigue. The lightweight structure makes them easily maneuverable, which is particularly beneficial for tasks that require precision casing or reaching difficult areas.

Another noteworthy characteristic is the Tool-less chain tensioning system. This feature allows users to adjust the chain tension quickly and without the need for additional tools, simplifying maintenance and enhancing user experience.

Overall, the Husqvarna 235 and 240 chainsaws are excellent choices for homeowners seeking reliable, efficient, and easy-to-use tools for light to moderate cutting tasks. With advanced features like X-Torq technology, safety mechanisms, and user-friendly designs, they represent a valuable addition to any gardening or outdoor toolkit.
Top Page Image Contents