Husqvarna 324RX Assembling the cutting equipment, Fitting the blade guard and saw blade, Assembly

Page 14
Assembling the cutting equipment

ASSEMBLY

Assembling the cutting equipment

WARNING!

! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting

! attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting attachment

! without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

Fitting a blade guard, grass blade and grass cutter

Fitting a blade guard, grass blade and grass cutter G

F

E

D G

A

B

 

Fitting the blade guard and saw bladeC

•Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt.

CAUTION! Use the recommended blade guard. See the Technical data section.

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D), support cup (E) and support flange

(F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

Fitting the blade guard and saw blade

K

J

HManual background

I

A

L

•Remove the mounting plate (H). Fit the adapter (I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents English 324RX-SeriesOperator’s manual EPA KEY TO SYMBOLS SymbolsNote the following before starting CONTENTSContents INTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw?GENERAL SAFETY PRECAUTIONS Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard Quick release MufflerCutting equipment Cutting equipmentLocking nut General rules Sharpening grass cutters and grass bladesSharpening the saw blade WARNING! Always discard a blade that isTrimmer head Transport position, handlebar ASSEMBLYFitting the handlebar Fitting the blade guard and saw blade Assembling the cutting equipmentFitting a blade guard, grass blade and grass cutter G F E DFitting a trimmer guard and Superauto II 1 trimmer head G F D B CStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments Correct height Correct balanceFuel FUEL HANDLINGFuel handling Fueling Starting and stopping STARTING AND STOPPINGCheck before starting For throttle handles with a start throttle lock WARNING! When the engine is started withWarm engine StartingWORKING TECHNIQUES General working instructionsThe ABC of clearing Forestry clearing using a saw blade Grass trimming with a trimmer head Grass clearing using a grass bladeBrush cutting with a saw blade TrimmingCutting SweepingMuffler MAINTENANCECarburetor Air filter Cooling systemSpark plug Cleaning the air filterOiling the air filter Bevel gearMaintenance schedule Check that the bevel gear is filled three-quarters full with lubricantTECHNICAL DATA Technical dataCutting attachment guard, Art. no Approved accessoriesType YOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENT2,4 mm Super AutoSuper Auto II 4,0 mPage Clic 8,5 m10 cm 4,2 m 2,4-2,7 mm4,25 m 2,4-2,7 mmT35, T35x 10 cm 4,3 mPage ´z+R=¶5I¨ ´z+R=¶5I¨
Top Page Image Contents