Husqvarna 324RX manual Starting And Stopping, Check before starting, Starting and stopping

Page 20
STARTING AND STOPPING

STARTING AND STOPPING

Check before starting

•Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

•Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.

•Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

•Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.

•Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.

•Never use the machine without a guard nor with a defective guard.

•All covers must be correctly fitted and undamaged before you start the machine.

Starting and stopping

WARNING! The complete clutch cover and

!shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Ensure the cutting attachment cannot come into contact with any object.

Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Cold engine

Ignition: Set the stop switch to the start position.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents English 324RX-SeriesOperator’s manual EPA KEY TO SYMBOLS SymbolsNote the following before starting CONTENTSContents INTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw?GENERAL SAFETY PRECAUTIONS Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard Quick release MufflerCutting equipment Cutting equipmentLocking nut Sharpening grass cutters and grass blades Sharpening the saw bladeGeneral rules WARNING! Always discard a blade that isTrimmer head Transport position, handlebar ASSEMBLYFitting the handlebar Assembling the cutting equipment Fitting a blade guard, grass blade and grass cutterFitting the blade guard and saw blade G F E DFitting a trimmer guard and Superauto II 1 trimmer head G F D B CStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments Correct height Correct balanceFuel FUEL HANDLINGFuel handling Fueling Starting and stopping STARTING AND STOPPINGCheck before starting WARNING! When the engine is started with Warm engineFor throttle handles with a start throttle lock StartingWORKING TECHNIQUES General working instructionsThe ABC of clearing Forestry clearing using a saw blade Grass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingCutting SweepingMuffler MAINTENANCECarburetor Cooling system Spark plugAir filter Cleaning the air filterOiling the air filter Bevel gearMaintenance schedule Check that the bevel gear is filled three-quarters full with lubricantTECHNICAL DATA Technical dataCutting attachment guard, Art. no Approved accessoriesType YOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENTSuper Auto Super Auto II2,4 mm 4,0 mPage 8,5 m 10 cm 4,2 mClic 2,4-2,7 mm4,25 m 2,4-2,7 mmT35, T35x 10 cm 4,3 mPage ´z+R=¶5I¨ ´z+R=¶5I¨
Top Page Image Contents