Husqvarna 324RX manual Technical Data, Technical data

Page 31

TECHNICAL DATA

Technical data

	324Rx
Engine
Cylinder displacement, cu.in/cm3	1,53/25,0
Cylinder bore, inch/mm	1,38/35
Stroke, inch/mm	1,03/26
Idle speed, rpm	3100
Recommended max. fast idle speed, rpm	11000
Speed of output shaft, rpm	8300
Max. engine output, acc. to ISO 8893, kW/ rpm	0,8 / 7000
Catalytic converter mufﬂer	No
Speed-regulated ignition system	No
Ignition system
Manufacturer/type of ignition system	Ikeda
Spark plug	NGK CMR5H
Electrode gap, inch/mm	0,024/0,6
Fuel and lubrication system
Manufacturer/type of carburetor	Walbro
Fuel tank capacity, US pint/litre	1,06/0,5
Weight

Weight without fuel, cutting attachment and guard, Lbs/kg

Sound levels

(see note 1)

Equivalent sound pressure level at the user′s ear, measured according to ANSI B175.3-1997, dB(A), min/max:

12,1/5,5

89/97

Vibration levels
Vibration levels at handles, measured according to ANSI
B175.3-1997, m/s2
At idle, left/right handles, min.:	1,3/1,3
At idle, left/right handles, max.:	1,7/1,6
At max. speed, left/right handles, min.:	3,1/2,6
At max. speed, left/right handles, max.:	5,2/4,1

Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various

working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.

NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment ﬁtted. The table indicates the highest and lowest values.

English – 31

Image 31

Contents Operator’s manual EPA 324RX-SeriesEnglish Symbols KEY TO SYMBOLSContents CONTENTSNote the following before starting Dear customer INTRODUCTIONWhat is what on the clearing saw? WHAT IS WHAT?Personal protective equipment GENERAL SAFETY PRECAUTIONSThrottle lockout Machine′s safety equipmentCutting attachment guard Stop switchVibration damping system Mufﬂer Quick releaseLocking nut Cutting equipmentCutting equipment WARNING! Always discard a blade that is Sharpening grass cutters and grass bladesSharpening the saw blade General rulesTrimmer head Fitting the handlebar ASSEMBLYTransport position, handlebar G F E D Assembling the cutting equipmentFitting a blade guard, grass blade and grass cutter Fitting the blade guard and saw bladeG F D B C Fitting a trimmer guard and Superauto II 1 trimmer headFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness Correct balance Correct heightFuel handling FUEL HANDLINGFuel Fueling Check before starting STARTING AND STOPPINGStarting and stopping Starting WARNING! When the engine is started withWarm engine For throttle handles with a start throttle lockGeneral working instructions WORKING TECHNIQUESThe ABC of clearing Forestry clearing using a saw blade Trimming Grass clearing using a grass bladeBrush cutting with a saw blade Grass trimming with a trimmer headSweeping CuttingCarburetor MAINTENANCEMufﬂer Cleaning the air ﬁlter Cooling systemSpark plug Air ﬁlterBevel gear Oiling the air ﬁlterCheck that the bevel gear is ﬁlled three-quarters full with lubricant Maintenance scheduleTechnical data TECHNICAL DATAType Approved accessoriesCutting attachment guard, Art. no FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS4,0 m Super AutoSuper Auto II 2,4 mmPage 2,4-2,7 mm 8,5 m10 cm 4,2 m Clic2,4-2,7 mm 4,25 m10 cm 4,3 m T35, T35xPage ´z+R=¶5I¨ ´z+R=¶5I¨