Husqvarna 324RX manual Fitting other guards and cutting attachments, Standard harness, Assembly

Page 16
Fitting other guards and cutting attachments

ASSEMBLY

Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

To dismantle, follow the instructions in the reverse order.

Fitting other guards and cutting attachments

Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hook the guard onto the fitting on the shaft and secure it with the bolt (L).

Fit the drive disc (B) on the output shaft.

Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

Insert the locking pin (C) in the hole to lock the shaft.

Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

Adjusting the harness and clearing sawH

H

To dismantle, follow the instructions in the reverse order.

Adjusting the harness and clearing saw

WARNING! When using a clearing saw it

! must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release.

Standard harness

Quick release

At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness.

A

M

L B

Standard harnessC

Spreading the load on your shoulders

A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders.

16 – English

Image 16
Contents Operator’s manual EPA 324RX-SeriesEnglish KEY TO SYMBOLS SymbolsContents CONTENTSNote the following before starting INTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw?GENERAL SAFETY PRECAUTIONS Personal protective equipmentMachine′s safety equipment Throttle lockoutCutting attachment guard Stop switchVibration damping system Quick release MufflerLocking nut Cutting equipmentCutting equipment Sharpening grass cutters and grass blades Sharpening the saw bladeGeneral rules WARNING! Always discard a blade that isTrimmer head Fitting the handlebar ASSEMBLYTransport position, handlebar Assembling the cutting equipment Fitting a blade guard, grass blade and grass cutterFitting the blade guard and saw blade G F E DFitting a trimmer guard and Superauto II 1 trimmer head G F D B CFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness Correct height Correct balanceFuel handling FUEL HANDLINGFuel Fueling Check before starting STARTING AND STOPPINGStarting and stopping WARNING! When the engine is started with Warm engineFor throttle handles with a start throttle lock StartingWORKING TECHNIQUES General working instructionsThe ABC of clearing Forestry clearing using a saw blade Grass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingCutting SweepingCarburetor MAINTENANCEMuffler Cooling system Spark plugAir filter Cleaning the air filterOiling the air filter Bevel gearMaintenance schedule Check that the bevel gear is filled three-quarters full with lubricantTECHNICAL DATA Technical dataType Approved accessoriesCutting attachment guard, Art. no YOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENTSuper Auto Super Auto II2,4 mm 4,0 mPage 8,5 m 10 cm 4,2 mClic 2,4-2,7 mm4,25 m 2,4-2,7 mmT35, T35x 10 cm 4,3 mPage ´z+R=¶5I¨ ´z+R=¶5I¨