Porter-Cable D29833-038-0 instruction manual 12V DC Outlet, Before Start UP

Page 12

12V DC OUTLET

IMPORTANT: Allow generator to run at no load for 5 minutes upon each initial start-up to allow engine to stabilize.

IMPORTANT: When the unit is running the battery will charge. DO NOT connect the 12V DC cables to the generator’s battery.

To charge battery:

1.Using the 12V DC cables supplied, connect the red positive (+) 12V DC cable to the battery's positive (+) terminal.

2.Attach the other end of the red positive (+) 12V DC cable to the generators positive (+) 12V DC outlet.

3. Connect the black negative (-) 12V DC cable to the battery's negative (-) terminal.

4.Attach the other end of the black negative (-) 12V DC cable to the generators negative (-) 12V DC outlet.

5.Charge the battery according to battery or equipment manufacturer recommendations.

BEFORE START UP

This generator has been shipped from the factory without oil in the crankcase. Operating the unit without oil can damage the engine.

Always check engine oil level before every start. Running engine low of oil or out of oil could result in serious damage to the engine.

Follow the steps listed below before starting generator:

1.Check engine oil. Refer to the Engine Operator's Manual for correct grade and quantity of oil.

2. Check fuel level, fill as required. Make sure generator is turned off and has been allowed time to cool down. Use clean, fresh, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline.

Never fill fuel tank completely. Fill tank to 1/2" below the bottom of the filler neck to

provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

Never run engine indoors or in enclosed, poor ventilated areas, en- gine exhaust contains carbon monoxide, an odorless and deadly

gas.

3.Make sure generator is grounded in accordance with local requirements.

4.All electrical loads MUST be disconnected.

5.The idle control switch MUST be in the OFF position.

Engine speed has been factory set to provide safe operation. Tampering with the engine speed adjustment could result in over-

heating of attachments and could cause a fire. Never attempt to “speed-up” the en- gine to obtain more performance. Both the output voltage and frequency will be thrown out of standard by this practice, endangering attachments and the user.

You MUST unplug any load from the generator before starting to prevent permanent damage to any appliances.

D29833

12- ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Instruction Consumer General and Service Information Consumer Safety InformationSafety Guidelines / Definitions Important Safety InstructionsHazard What can Happen HOW to Prevent IT Risk of Fire Hazard What can Happen HOW to Prevent IT Unit Indoors or in ANYConfined Area Fire, Inhalation Damage toVehicle Surfaces GasolineRisk of Unsafe Operation VoltageSensitive appli Ances without aSpecifications Risk from Lifting Hazard What can Happen HOW to Prevent ITModel Assembly Remove Generator from CartonOther Loose Parts Grounding the GeneratorDouble Throw Transfer Switch Obtaining Electricity from the GeneratorExtension Cords Operation 12V DC Outlet Before Start UPTo Start the Engine Odorless and deadly gasConnecting Electrical Loads Stopping EngineMaintenance Engine MaintenanceGenerator Maintenance Customer Responsibilities TableStorage Engine PreparationGenerator Wattage Calculations Determining Wattage RequirementsTotal Application Guide Starting Wattage RequirementsHousehold Wattage Calculator Typical Device Wattage TotalTroubleshooting Guide Problem Cause CorrectionLimited Warranty Responsibility of Original Purchaser initial UserQuick Facts Always Refer to the Manuals Supplied with this UnitManual de Información General Y DE Servicio Pautas DE SEGURIDAD/DEFINICIONES Instrucciones Importantes DE SeguridadRiesgo ¿QUÉ Puede OCURRIR? ¿CÓMO PREVENIRLO? Subdimensionados Riesgo DE Incendio Y Electrocución continuaciónOperación del Generador bajoIntentar llenar el Tanque de comBustible mientras El motor está enIncendio Inhalación, daños aLas superficies del VehículoRiesgo DE Operación Insegura continuación Operación deEquipos sensibles Las fluctuacionesTabla DE Especificaciones ModeloInstalación Sacar EL Generador DE LA CajaOtras Partes Sueltas Conexión a Tierra DEL GeneradorAbasteciéndose DE Electricidad DEL Generador Cables DE Extensión EléctricaInterruptor DE Transferencia DE Doble Hoja Familiarizarse CON EL Generador Capacidad DEL GeneradorInterruptores DE Circuito Dispositivo DE Apagado POR Poco AceiteSalida Para 12 Antes DE ArrancarPara cargar la batería Para operar el equipo de 12 V de CCArranque Manual DEL Motor Parando EL Motor Conexión DE Artefactos EléctricosPrograma DE Mantenimiento Cartilla DE Responsabilidades DEL ClienteRecomendaciones Generales Mantenimiento DEL MotorAlmacenaje Preparación DEL MotorGenerador Importante Determinando LOS Requerimientos DE PotenciaVatios de Funcionamiento Vatios de Funcionamiento Vatios de ArranquePotencia Requerida Para EL Arranque Volts X Ampers = Vatios Volts x 10 ampers = 1 200 WPrecaucion Calculo DE Potencia DomésticaGuía Para Diagnóstico DE Problemas Problema Causa CorrecciónGarantía Limitada Responsabilidad DEL Comprador Original Usuario inicialInformacion Rapida Sobre Generadores Manuel Renseignements Pour LE Consommateur Mesures DE Sécurité Définitions Mesures DE Sécurité ImportantesRisques Délectrocution ET D’INCENDIE Risques Délectrocution ET D’INCENDIE suite RisqueRisques D’INCENDIE Risques AUX Voies Respiratoires ET Risques D’INHALATION Risques D’UNE UtilisationRisques Reliés AUX Surfaces Chaudes Spécifications Risques Reliés AUX Pièces MobilesRisques Lors DU Levage Retrait DE LA Génératrice DE SON Emballage Autres Pièces DétachéesMise À LA Terre DE LA Génératrice Patte de mise à la terreComment Obtenir DE L’ÉLECTRICITÉ DE LA Génératrice RallongesInverseur Bidirectionnel De filUtilisation Prise DE Courant Continu DE 12 Avant DE Démarrer LE MoteurChargement de la batterie Endommager le moteurDémarrage DU Moteur Arrêt DU Moteur Branchement DE Charges ÉlectriquesRecommandations Générales EntretienTableau DES Responsabilités DU Client Entretien DU MoteurEntreposage Préparation DU MoteurGénératrice Puissance de service Puissance d’amorçage Puissance de serviceCalcul DE LA Puissance EN Watts Détermination DES Exigences DE Puissance EN WattsPuissance D’AMORÇAGE EN Watts Volts x ampères = watts Volts x 10 ampères = 1 200 wattsCalcul DE LA Puissance EN Watts Mise EN GardeGuide DE Dépannage Problème Cause CorrectionGarantie Limitée Responsabilité DE Lacheteur Dorigine utilisateur initialRemarque 67- FR Faits Saillants Toujours Consulter LES Guides Fournis Avec CET Appareil

D29833-038-0 specifications

The Porter-Cable D29833-038-0 is a versatile and powerful tool designed to cater to a variety of demanding applications, making it a favorite among both professionals and DIY enthusiasts. Known for its durability and performance, this model stands out in the competitive market of woodworking and construction tools.

One of the key features of the D29833-038-0 is its robust motor, which provides ample power for a range of tasks, from sanding to cutting. With a strong horsepower rating, this tool ensures efficiency and effectiveness, enabling users to complete projects in a fraction of the time it would typically take with less powerful equipment.

The design of the Porter-Cable D29833-038-0 emphasizes user comfort and control. It comes equipped with an ergonomic handle that reduces user fatigue during extended use. This aspect is particularly beneficial for those who manage large-scale projects or spend several hours on the job. The thoughtful design extends to its weight distribution, allowing for better maneuverability without compromising stability.

In addition to its physical characteristics, the D29833-038-0 features advanced technology that enhances its functionality. This includes variable speed settings that allow users to adjust the tool's performance based on the material and task at hand, thus providing greater versatility. The integrated dust collection system minimizes mess and ensures a cleaner workspace, which is essential for maintaining focus and safety during operations.

Another noteworthy characteristic is the compatibility of the D29833-038-0 with a wide range of accessories and attachments. This adaptability enables users to switch between tasks seamlessly, whether they're sanding, cutting, or shaping materials. The convenience of quick-release mechanisms also ensures that changing accessories is both quick and hassle-free.

Safety features have not been overlooked in the design of the Porter-Cable D29833-038-0. The tool is built with protective guards and features that help prevent accidents, making it suitable for users of varying experience levels.

In summary, the Porter-Cable D29833-038-0 combines power, ergonomic design, advanced technology, and safety features, making it an outstanding choice for anyone looking to enhance their toolkit. Whether you’re a professional contractor or a passionate DIYer, this tool is designed to deliver reliable performance across multiple applications, ensuring that every project is completed with precision and ease.
Top Page Image Contents