RedMax BCZ3000SW manual  16 , Recommended Mixing Ratio Gasoline 50OIL, HOW to MIX Fuel

Page 16

7. Fuel

WARNING

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.

The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE)

Do not use BIA or TCW (2-stroke water- cooling type) mixed oil.

16

RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1

50:1 MIXING CHART

GASOLINE gal. 1 2 3 4 5

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE liter 1

2

3

4

5

2-CYCLE OIL ml 20 40 60 80 100

Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)

If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate

Image 16
Contents BCZ3000SW BCZ3000SWPage Safety First ContentsParts location Specifications 4   5  Symbols on the machine  6 For safe operation Working ConditionWorking Circumstance  7 Working Plan  8 Starting the Engine Before Starting the Engine 9  Using the Product  10 Maintenance If Someone ComesHandling Fuel  11 Transportation  12   13  SE5 Mounting Engine SE5SE6 SE7 SE8 Putting on Waist PADInstalling Cutting Head SE10 SE9Balance Unit  15 HOW to MIX Fuel Fuel 16  Recommended Mixing Ratio Gasoline 50OILFueling the Unit For Your Engine LIFE, AvoidOperation OP1OP3 OP4 Starting Engine 19  OP7 Adjusting the Line Length 20  Maintenance Maintenance ChartMA1 Refilling Trimming Line MA1  21  22  MA5 MA6 Muffler Spark ArresterGear Case MA6 Intake AIR Cooling VentProcedures to be Performed After Every 100 Hours of USE StorageMA8  24 Optional blade usage  25 OPT2 OPT3 SET UP the Blade StandardOPT4 OPT5OPT6 OPT7 OPT8 Cutting MethodOperation  27  28  OPT9Controlling Blade Bounce Maintenance Blade OPT10Transporting the Unit  29 Check Probable Causes Action Troubleshooting guide 30  Parts list  31 Drive Unit BCZ3000S S/N 300001 and up  32 Optional Blade & Accessories  33 Drive Unit BCZ3000SW S/N 300001 and up  34  35   36   37  Part Number Description QtyManufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée