Simplicity Cobalt Series manual Starting the Engine, Stopping the Rider

Page 21

WARNING

Read the Operator’s Manual before attempting to operate the machine.

•If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES and CONTROLS section, do so now.

•Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

Starting the Engine

1.While sitting in the operator’s seat, engage the parking brake and make sure the PTO switch is disengaged and the motion control handles are locked in the NEUTRAL position.

2.NOTE: A warm engine may not require choking.

Set the engine throttle control to FAST throttle position. Then fully close the choke by pulling the knob OUT fully.

3.Insert the key into the ignition switch and turn it to

START.

4.After the engine starts, gradually open the choke (push knob down fully). Reduce to half throttle speed and allow to warm up.

Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider.

5.After warming the engine, ALWAYS operate the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in Stopping the Rider.

Operation

Stopping the Rider

1.Returning the ground speed control levers to the middle position will stop rider movement. Pivot the levers outward and lock them in NEUTRAL.

2.Disengage the PTO by pushing down on the PTO switch.

3.Engage the parking brake by pulling the handle up until it locks into position.

4.Move the throttle control to mid-throttle position and turn the ignition key to OFF. Remove the key.

Safety

Controls

Operation

Maintenance Troubleshooting Specifications

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 5900763 30HP Zero-Turn Riders Mfg. No DescriptionDate Purchased Table of Contents Operating Safety Operator SafetyRead the Manual ChildrenSlope Operation Thrown ObjectsMoving Parts Roll Bar Use Retaining Walls, Drop-offs, and WaterOverhead Obstacles Enclosed Areas Fuel and MaintenanceControls Operation Troubleshooting Maintenance SafetySpecifications General OperationEmissions Towed Equipment Ride-On UnitsIgnition System Operating on steep slopes can be dangerousService and Maintenance Service & MaintenanceSafe Handling of Gasoline Roll Bar Instructions Operational WarningsInspection of the Roll Bar Protective Structure Inspection and Maintenance of the Roll Bar Seat Belt Safety Decals Safety Controls OperationOperational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsIdentification Numbers Features and ControlsCE Models CE Identification Tag MarkingsTroubleshooting Safety Controls Operation MaintenancePTO Power Take Off Switch Parking BrakeHour Meter / Maintenance Reminder Ignition SwitchSeat Adjustment Lever Throttle ControlGeneral Operating Safety OperationChecks Before Starting Check Tire Pressures Seat AdjustmentPushing the Rider by Hand Tire PressureMowing Height Adjustment Foot Pedal AdjustmentTo Adjust Pedal Position Insert the key into the ignition switch and turn it to Starting the EngineStopping the Rider Forward Travel Practice Zero-Turn Driving PracticeSmooth Travel Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn TurningRaise and Lower the Roll Bar Specifications TroubleshootingTo Lower the Roll Bar To Raise the Roll BarMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions How Much Grass to MulchRegular Maintenance Maintenance ScheduleCheck Rider / Mower for loose hardware Fuel Filter Checking / Adding FuelChange Oil & Filter Remove the shop cloth and wipe up any spilled oilChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Grease LubricationOil Lubricating the Front CastersServicing The Mower Blades Safety Controls Operation Troubleshooting MaintenanceInspecting the Mower Blades Never weld or straighten bent mower bladesSpecifications Reinstalling the Mower BladesBattery Maintenance Battery ChargingCleaning the Battery and Cables Keep open flames and sparks away from the batterySpeed Balancing Adjustment Ground Speed Control Lever AdjustmentReturn-to-Neutral Adjustment Neutral AdjustmentChecking the Adjustment AdjustmentHydraulic Pump Drive Belt Replacement Parking Brake AdjustmentTo adjust the spring pre-load Suspension AdjustmentSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksDeck Lift Rod Timing Adjustment Deck Lift Spring Regular MaintenanceTo avoid damaging belts, do not pry belts over pulleys Mower Belt ReplacementSafety Controls TroubleshootingOperation Specifications Troubleshooting Maintenance Troubleshooting the RiderTroubleshooting the Mower Troubleshooting the RiderTroubleshooting Common Cutting Problems Operation MaintenanceTechnical Manuals SpecificationsControls Operation HP Briggs & StrattonOperation Controls Safety This page Intentionally Blank Belts and Blades Product Quick Specs

Cobalt Series specifications

The Simplicity Cobalt Series is an innovative line of gardening equipment that blends performance, durability, and ease of use. Designed for both amateur gardeners and seasoned professionals, the Cobalt Series reflects a commitment to cutting-edge technology and thoughtful design, making garden maintenance enjoyable and efficient.

One of the standout features of the Cobalt Series is its lightweight yet robust construction. Utilizing advanced materials, these tools minimize user fatigue, allowing for prolonged usage without discomfort. The ergonomic design of the handles ensures a comfortable grip, promoting natural hand movements which reduces strain during gardening tasks.

The Cobalt Series integrates smart technology into its product lineup. Many of the tools are equipped with a unique power management system, optimizing battery life and enhancing efficiency. This means users can accomplish more with less time spent recharging. Additionally, select models feature wireless connectivity, allowing gardeners to track their usage, receive maintenance reminders, and access instructional content through a dedicated app.

A key characteristic of the Cobalt Series is versatility. The range includes a variety of tools such as electric trimmers, mowers, and blowers, all designed to tackle different gardening tasks with ease. Each tool is engineered for optimal performance, boasting powerful motors that ensure effective cutting and cleaning. Whether it’s mowing a lawn, trimming hedges, or blowing leaves, users can trust the Cobalt Series to deliver professional results.

Moreover, the Cobalt Series prioritizes safety, incorporating features like automatic shut-off and safety guards. These enhancements not only protect the user but also ensure that the equipment remains in top condition during operation.

In terms of maintenance, the Cobalt Series tools are designed to be hassle-free. Many models include self-cleaning mechanisms and robust components that require minimal upkeep. This focus on reliability means that gardeners can spend more time enjoying their outdoor spaces and less time on repairs.

Finally, with a sleek and modern aesthetic, the Simplicity Cobalt Series not only performs well but also looks great in any garden shed or workspace. Overall, the Cobalt Series is a testament to Simplicity’s dedication to combining innovation with practical gardening solutions. Whether you are rejuvenating your garden or maintaining a landscape, the tools from the Cobalt Series are sure to enhance your gardening experience.
Top Page Image Contents