Simplicity Cobalt Series Safety, Controls Operation Troubleshooting Maintenance, Specifications

Page 8

Safety

Operator Safety

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is

capable of amputating hands and feet and throwing objects. The triangle in text signifies important

cautions or warnings which must be followed.

Controls

Operation

Troubleshooting Maintenance

General Operation

1.Read, understand, and follow all instructions in the manual and on the unit before starting.

2.Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

3.Only allow responsible adults, who are familiar with the instructions, to operate the unit (local regulations can restrict operator age).

4.Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade(s).

5.Be sure the area is clear of other people before mowing. Stop the unit if anyone enters the area.

6.Never carry passengers.

7.Do not mow in reverse unless absolutely necessary. Always look down and behind before and while travelling in reverse.

8.Never direct discharge material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blade(s) when crossing gravel surfaces.

9.Do not operate the machine without the entire grass catcher, discharge guard (deflector), or other safety devices in place and operational.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disengage the blades (PTO), set parking brake, stop engine, and remove keys before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial light.

14. Do not operate the unit while under the influence of alcohol or drugs.

15Watch for traffic when operating near or crossing roadways.

16. Use extra care when loading or unloading the unit into a trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and above, are involved in a large percentage of power equipment- related injuries. These operators should evaluate their ability to operate the equipment safely enough to protect themselves and others from injury.

19. Follow the manufacturer’s recommendations for wheel weights or counterweights.

20. Keep in mind the operator is responsible for accidents occurring to other people or property.

21. All drivers should seek and obtain professional and practical instruction.

22. Always wear substantial footwear and trousers. Never operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades and blade hardware are present, intact, and secure. Replace worn or damaged parts.

24. Disengage attachments before: refueling, removing an attachment, making adjustments (unless the adjustment can be made from the operator’s position).

25. When the machine is parked, stored, or left unattended, lower the cutting means unless a positive mechanical lock is used.

26. Before leaving the operator’s position for any reason, engage the parking brake (if equipped), disengage the blades (PTO), stop the engine, and remove the key.

27. To reduce fire hazard, keep the unit free of grass, leaves,

&excess oil. Do not stop or park over dry leaves, grass, or combustible materials.

28. OSHA regulations may require the use of hearing protection when exposed to sound levels greater than 85 dBA for an 8 hour time period.

WARNING

It is a violation of California Public Resource Code, Section 4442, to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust system is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order. Other states or federal jurisdictions may have similar laws. Contact an Authorized Service Dealer to obtain a spark arrester designed for the exhaust system installed on this engine.

WARNING

Extended exposure to excessively high sound levels can result in hearing loss.

This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause hearing loss through extended periods of exposure.

Wear hearing protection when operating this machine.

Specifications

Transporting and Storage

1.When transporting the unit on an open trailer, make sure it is facing forward, in the direction of travel. If the unit is facing backwards, wind lift could damage the unit.

2.Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage.

3.Never store the unit (with fuel) in an enclosed poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Fuel vapor is also toxic to humans and animals.

4.Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods.

5.Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.

6.Never store the unit or fuel container inside where there is an open flame or pilot light, such as in a water heater. Allow unit to cool before storing.

6

www.simplicitymfg.com

Image 8 Contents
30HP Zero-Turn Riders Mfg. No Description 5900763Date Purchased Table of Contents Operator Safety Operating Safety Read the Manual ChildrenMoving Parts Slope OperationThrown Objects Overhead Obstacles Roll Bar UseRetaining Walls, Drop-offs, and Water Fuel and Maintenance Enclosed AreasSafety Controls Operation Troubleshooting MaintenanceSpecifications General OperationTowed Equipment Ride-On Units EmissionsIgnition System Operating on steep slopes can be dangerousSafe Handling of Gasoline Service and MaintenanceService & Maintenance Inspection of the Roll Bar Protective Structure Roll Bar InstructionsOperational Warnings Inspection and Maintenance of the Roll Bar Seat Belt Safety Controls Operation Safety DecalsSafety Interlock System Operational Safety ChecksSafety Icons North American Safety IconsFeatures and Controls Identification NumbersCE Models CE Identification Tag MarkingsSafety Controls Operation Maintenance TroubleshootingPTO Power Take Off Switch Parking BrakeIgnition Switch Hour Meter / Maintenance ReminderSeat Adjustment Lever Throttle ControlChecks Before Starting General Operating SafetyOperation Seat Adjustment Check Tire PressuresPushing the Rider by Hand Tire PressureTo Adjust Pedal Position Mowing Height AdjustmentFoot Pedal Adjustment Stopping the Rider Insert the key into the ignition switch and turn it toStarting the Engine Zero-Turn Driving Practice Forward Travel PracticeSmooth Travel Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningSpecifications Troubleshooting Raise and Lower the Roll BarTo Lower the Roll Bar To Raise the Roll BarMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Attaching a Trailer Proper MulchingMulching Requires Excellent Mowing Conditions How Much Grass to MulchCheck Rider / Mower for loose hardware Regular MaintenanceMaintenance Schedule Checking / Adding Fuel Fuel FilterChange Oil & Filter Remove the shop cloth and wipe up any spilled oilChange Interval Every 250 Hours Filter Part Number Change Hydraulic Oil FilterCheck Hydraulic Oil Level Lubrication GreaseOil Lubricating the Front CastersSafety Controls Operation Troubleshooting Maintenance Servicing The Mower BladesInspecting the Mower Blades Never weld or straighten bent mower bladesReinstalling the Mower Blades SpecificationsBattery Charging Battery MaintenanceCleaning the Battery and Cables Keep open flames and sparks away from the batteryGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Return-to-Neutral AdjustmentChecking the Adjustment AdjustmentParking Brake Adjustment Hydraulic Pump Drive Belt ReplacementSuspension Adjustment To adjust the spring pre-loadSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksDeck Lift Rod Timing Adjustment Regular Maintenance Deck Lift SpringMower Belt Replacement To avoid damaging belts, do not pry belts over pulleysTroubleshooting Safety ControlsOperation Specifications Troubleshooting Maintenance Troubleshooting the RiderTroubleshooting the Rider Troubleshooting the MowerOperation Maintenance Troubleshooting Common Cutting ProblemsSpecifications Technical ManualsControls Operation HP Briggs & StrattonOperation Controls Safety This page Intentionally Blank Product Quick Specs Belts and Blades