Simplicity Cobalt Series manual Return-to-Neutral Adjustment, Checking the Adjustment

Page 36

Safety

Controls

Operation

Specifications Troubleshooting Maintenance

Regular Maintenance

Neutral Adjustment

If the tractor “creeps” while the ground speed control levers are locked in NEUTRAL, then it may be necessary to adjust the linkage rod.

1.Park the machine on a hard, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, and turn off the engine.

CAUTION

This adjustment should not be performed while the machine is running.

2.The locking nuts (D, Figure 35) are to be used together to turn the rod. Loosen the jam nut that locks against the ball joint (B) and turn the linkage rod (A) to adjust:

If the machine creeps forward, turn the rod clockwise (while standing at the rear of the machine, facing forward);

If the machine creeps backward, turn the rod counter- clockwise (while standing at the rear of hte machine, facing foward).

3.Lock the jam nut (B) against the ball joint (C) when neutral is achieved.

4.Start the engine.

5.Disengage the parking brake and lock the ground speed control levers in the neutral position.

6.If the machine still “creeps,” repeat the Neutral Adjustment procedure. It may take several attempts to achieve neutral, depending on how much the machine creeps.

Return-to-Neutral Adjustment

Checking the Adjustment:

To determine if it is necessary to adjust the neutral return, perform the following steps.

1.Disengage the PTO, engage the parking brake and turn off the engine.

2.Move the ground speed control levers into the operating position, pull levers rearward and release.

3.Move the ground speed control levers out towards the neutral position. If the levers do not align with the notches in the neutral lock plate, it is necessary to adjust the neutral return rod.

B D

A

Figure 35. Neutral Adjustment (RH side shown)

A.Adjustment Linkage Rod

B.Jam Nut

C.Ball Joint

D.Locking Nuts

A

B

Figure 36. Return to Neutral Adjustment

A.Return Spring

B.Set Collar

Adjustment:

1.Loosen the set collar (B, Figure 36) locked against the return spring (A).

2.Lock the ground speed control levers in neutral.

3.Tighten set collar snug against the return spring.

4.Pull lever rearward and release to check that the lever stops aligned with notch in the neutral lock plate.

It is important to note that after every adjustment of the neutral return spring, the lever must be returned to locked position to properly check the neutral position.

34

www.simplicitymfg.com

Image 36
Contents 30HP Zero-Turn Riders Mfg. No Description 5900763Date Purchased Table of Contents Operator Safety Operating SafetyRead the Manual ChildrenSlope Operation Thrown ObjectsMoving Parts Roll Bar Use Retaining Walls, Drop-offs, and WaterOverhead Obstacles Fuel and Maintenance Enclosed AreasSafety Controls Operation Troubleshooting MaintenanceSpecifications General OperationTowed Equipment Ride-On Units EmissionsIgnition System Operating on steep slopes can be dangerousService and Maintenance Service & MaintenanceSafe Handling of Gasoline Roll Bar Instructions Operational WarningsInspection of the Roll Bar Protective Structure Inspection and Maintenance of the Roll Bar Seat Belt Safety Controls Operation Safety DecalsSafety Interlock System Operational Safety ChecksSafety Icons North American Safety IconsFeatures and Controls Identification NumbersCE Models CE Identification Tag MarkingsSafety Controls Operation Maintenance TroubleshootingPTO Power Take Off Switch Parking BrakeIgnition Switch Hour Meter / Maintenance ReminderSeat Adjustment Lever Throttle ControlGeneral Operating Safety OperationChecks Before Starting Seat Adjustment Check Tire PressuresPushing the Rider by Hand Tire PressureMowing Height Adjustment Foot Pedal AdjustmentTo Adjust Pedal Position Insert the key into the ignition switch and turn it to Starting the EngineStopping the Rider Zero-Turn Driving Practice Forward Travel PracticeSmooth Travel Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningSpecifications Troubleshooting Raise and Lower the Roll BarTo Lower the Roll Bar To Raise the Roll BarMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Attaching a Trailer Proper MulchingMulching Requires Excellent Mowing Conditions How Much Grass to MulchRegular Maintenance Maintenance ScheduleCheck Rider / Mower for loose hardware Checking / Adding Fuel Fuel FilterChange Oil & Filter Remove the shop cloth and wipe up any spilled oilChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Lubrication GreaseOil Lubricating the Front CastersSafety Controls Operation Troubleshooting Maintenance Servicing The Mower BladesInspecting the Mower Blades Never weld or straighten bent mower bladesReinstalling the Mower Blades SpecificationsBattery Charging Battery MaintenanceCleaning the Battery and Cables Keep open flames and sparks away from the batteryGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Return-to-Neutral AdjustmentChecking the Adjustment AdjustmentParking Brake Adjustment Hydraulic Pump Drive Belt ReplacementSuspension Adjustment To adjust the spring pre-loadSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksDeck Lift Rod Timing Adjustment Regular Maintenance Deck Lift SpringMower Belt Replacement To avoid damaging belts, do not pry belts over pulleysTroubleshooting Safety ControlsOperation Specifications Troubleshooting Maintenance Troubleshooting the RiderTroubleshooting the Rider Troubleshooting the MowerOperation Maintenance Troubleshooting Common Cutting ProblemsSpecifications Technical ManualsControls Operation HP Briggs & StrattonOperation Controls Safety This page Intentionally Blank Product Quick Specs Belts and Blades

Cobalt Series specifications

The Simplicity Cobalt Series is an innovative line of gardening equipment that blends performance, durability, and ease of use. Designed for both amateur gardeners and seasoned professionals, the Cobalt Series reflects a commitment to cutting-edge technology and thoughtful design, making garden maintenance enjoyable and efficient.

One of the standout features of the Cobalt Series is its lightweight yet robust construction. Utilizing advanced materials, these tools minimize user fatigue, allowing for prolonged usage without discomfort. The ergonomic design of the handles ensures a comfortable grip, promoting natural hand movements which reduces strain during gardening tasks.

The Cobalt Series integrates smart technology into its product lineup. Many of the tools are equipped with a unique power management system, optimizing battery life and enhancing efficiency. This means users can accomplish more with less time spent recharging. Additionally, select models feature wireless connectivity, allowing gardeners to track their usage, receive maintenance reminders, and access instructional content through a dedicated app.

A key characteristic of the Cobalt Series is versatility. The range includes a variety of tools such as electric trimmers, mowers, and blowers, all designed to tackle different gardening tasks with ease. Each tool is engineered for optimal performance, boasting powerful motors that ensure effective cutting and cleaning. Whether it’s mowing a lawn, trimming hedges, or blowing leaves, users can trust the Cobalt Series to deliver professional results.

Moreover, the Cobalt Series prioritizes safety, incorporating features like automatic shut-off and safety guards. These enhancements not only protect the user but also ensure that the equipment remains in top condition during operation.

In terms of maintenance, the Cobalt Series tools are designed to be hassle-free. Many models include self-cleaning mechanisms and robust components that require minimal upkeep. This focus on reliability means that gardeners can spend more time enjoying their outdoor spaces and less time on repairs.

Finally, with a sleek and modern aesthetic, the Simplicity Cobalt Series not only performs well but also looks great in any garden shed or workspace. Overall, the Cobalt Series is a testament to Simplicity’s dedication to combining innovation with practical gardening solutions. Whether you are rejuvenating your garden or maintaining a landscape, the tools from the Cobalt Series are sure to enhance your gardening experience.