Simplicity Cobalt Series manual Mowing Recommendations, Height of Grass

Page 25

Mowing

Before mowing, set the cutting height as described in the Operation section.

1.Engage the parking brake. Make sure the PTO switch is disengaged and the ground speed control levers are in the NEUTRAL position.

2.Start the engine (see Starting the Engine).

3.Set the throttle to FULL.

4.Engage the PTO by pulling up on the PTO switch (E, Figure 1).

5.Begin mowing. See Mowing Recommendations section for tips on mowing patterns and lawn care. See Troubleshooting section for information on troubleshooting common cutting problems.

6.When finished, shut off the PTO.

7.Stop the engine (see Stopping the Rider).

Mowing Recommendations

Several factors can affect how well your machine cuts grass, Following proper mowing recommendations can improve the performance and life of your machine.

Height of Grass

Often cutting height is a matter of personal preference. Typically, you should mow the grass when it is is between three and five inches high. The proper cutting height range for a specific lawn will depend upon several factors, including the type of grass, the amount of rainfall, the prevailing temperature, and the lawn’s overall condition.

Cutting the grass too short causes weak, thin grass plants, which are easily damaged by dry periods and pests. Cutting too short is often more damaging than allowing the grass to be slightly higher.

Letting grass grow a bit longer—especially when it is hot and dry—reduces heat build-up, preserves needed moisture and protects the grass from heat damage and other problems. However, allowing grass to grow too high can cause thin turf and additional problems.

Cutting off too much at one time shocks the plant’s growth system and weakens the grass plants. A good rule of thumb is the 1/3 rule: to cut no more than one third of the grass height, and never more than 1 inch at a time.

The amount of grass you are able to cut in one pass is also effected by the type of mowing system you are using (for example, broadcasting with side discharge decks can process a much larger volume of grass than mulching does).

Operation

Figure 14. Proper Cutting Height

Tall Grass Requires Incremental Cutting

For extremely tall grass, set the cutting height at maximum for the first pass, and then reset it to the desired height and mow a second or third time.

Don’t cover the grass surface with a heavy layer of clippings. Consider using a grass collection system and starting a compost pile.

Cut Here On

 

 

 

Cut

First Pass

 

Here On

 

 

Second

 

 

 

Pass

 

 

 

Figure 15. Incremental Cutting

Safety

Controls

Operation

Maintenance Troubleshooting Specifications

23

Image 25
Contents 5900763 30HP Zero-Turn Riders Mfg. No DescriptionDate Purchased Table of Contents Operating Safety Operator SafetyRead the Manual ChildrenThrown Objects Slope OperationMoving Parts Retaining Walls, Drop-offs, and Water Roll Bar UseOverhead Obstacles Enclosed Areas Fuel and MaintenanceControls Operation Troubleshooting Maintenance SafetySpecifications General OperationEmissions Towed Equipment Ride-On UnitsIgnition System Operating on steep slopes can be dangerousService & Maintenance Service and MaintenanceSafe Handling of Gasoline Operational Warnings Roll Bar InstructionsInspection of the Roll Bar Protective Structure Inspection and Maintenance of the Roll Bar Seat Belt Safety Decals Safety Controls OperationOperational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsIdentification Numbers Features and ControlsCE Models CE Identification Tag MarkingsTroubleshooting Safety Controls Operation MaintenancePTO Power Take Off Switch Parking BrakeHour Meter / Maintenance Reminder Ignition SwitchSeat Adjustment Lever Throttle ControlOperation General Operating SafetyChecks Before Starting Check Tire Pressures Seat AdjustmentPushing the Rider by Hand Tire PressureFoot Pedal Adjustment Mowing Height AdjustmentTo Adjust Pedal Position Starting the Engine Insert the key into the ignition switch and turn it toStopping the Rider Forward Travel Practice Zero-Turn Driving PracticeSmooth Travel Reverse Travel PracticePractice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn TurningRaise and Lower the Roll Bar Specifications TroubleshootingTo Lower the Roll Bar To Raise the Roll BarMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions How Much Grass to MulchMaintenance Schedule Regular MaintenanceCheck Rider / Mower for loose hardware Fuel Filter Checking / Adding FuelChange Oil & Filter Remove the shop cloth and wipe up any spilled oilCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Grease LubricationOil Lubricating the Front CastersServicing The Mower Blades Safety Controls Operation Troubleshooting MaintenanceInspecting the Mower Blades Never weld or straighten bent mower bladesSpecifications Reinstalling the Mower BladesBattery Maintenance Battery ChargingCleaning the Battery and Cables Keep open flames and sparks away from the batterySpeed Balancing Adjustment Ground Speed Control Lever AdjustmentReturn-to-Neutral Adjustment Neutral AdjustmentChecking the Adjustment AdjustmentHydraulic Pump Drive Belt Replacement Parking Brake AdjustmentTo adjust the spring pre-load Suspension AdjustmentSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksDeck Lift Rod Timing Adjustment Deck Lift Spring Regular MaintenanceTo avoid damaging belts, do not pry belts over pulleys Mower Belt ReplacementSafety Controls TroubleshootingOperation Specifications Troubleshooting Maintenance Troubleshooting the RiderTroubleshooting the Mower Troubleshooting the RiderTroubleshooting Common Cutting Problems Operation MaintenanceTechnical Manuals SpecificationsControls Operation HP Briggs & StrattonOperation Controls Safety This page Intentionally Blank Belts and Blades Product Quick Specs

Cobalt Series specifications

The Simplicity Cobalt Series is an innovative line of gardening equipment that blends performance, durability, and ease of use. Designed for both amateur gardeners and seasoned professionals, the Cobalt Series reflects a commitment to cutting-edge technology and thoughtful design, making garden maintenance enjoyable and efficient.

One of the standout features of the Cobalt Series is its lightweight yet robust construction. Utilizing advanced materials, these tools minimize user fatigue, allowing for prolonged usage without discomfort. The ergonomic design of the handles ensures a comfortable grip, promoting natural hand movements which reduces strain during gardening tasks.

The Cobalt Series integrates smart technology into its product lineup. Many of the tools are equipped with a unique power management system, optimizing battery life and enhancing efficiency. This means users can accomplish more with less time spent recharging. Additionally, select models feature wireless connectivity, allowing gardeners to track their usage, receive maintenance reminders, and access instructional content through a dedicated app.

A key characteristic of the Cobalt Series is versatility. The range includes a variety of tools such as electric trimmers, mowers, and blowers, all designed to tackle different gardening tasks with ease. Each tool is engineered for optimal performance, boasting powerful motors that ensure effective cutting and cleaning. Whether it’s mowing a lawn, trimming hedges, or blowing leaves, users can trust the Cobalt Series to deliver professional results.

Moreover, the Cobalt Series prioritizes safety, incorporating features like automatic shut-off and safety guards. These enhancements not only protect the user but also ensure that the equipment remains in top condition during operation.

In terms of maintenance, the Cobalt Series tools are designed to be hassle-free. Many models include self-cleaning mechanisms and robust components that require minimal upkeep. This focus on reliability means that gardeners can spend more time enjoying their outdoor spaces and less time on repairs.

Finally, with a sleek and modern aesthetic, the Simplicity Cobalt Series not only performs well but also looks great in any garden shed or workspace. Overall, the Cobalt Series is a testament to Simplicity’s dedication to combining innovation with practical gardening solutions. Whether you are rejuvenating your garden or maintaining a landscape, the tools from the Cobalt Series are sure to enhance your gardening experience.