Jonsered CC 2145 manual General Safety Precautions, Locking nut, Locking screw

Page 11

WARNING! Mufﬂers ﬁtted with catalytic

GENERAL SAFETY PRECAUTIONS

For mufﬂers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and servicing the machine’s safety equipment.

Never use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to the machine.

If the mufﬂer on your machine is ﬁtted with a spark arrestor screen this must be cleaned regularly. A blocked screen will cause the engine to overheat and may lead to serious damage.

WARNING! Mufﬂers ﬁtted with catalytic

!converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of ﬁre!

WARNING! The inside of the mufﬂer contain

!chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged mufﬂer.

WARNING! The exhaust fumes from the

!engine are hot and may contain sparks which can start a ﬁre. Never start the machine indoors or near combustible material!

Locking nut

A locking nut is used to secure some types of cutting attachment.

When ﬁtting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.)

When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

Locking screw

The lock screw must be tightened securely for ball-bearing- mounted support cups.

English – 11

Image 11

Contents Operator’s manual EPA Symbols KEY TO SYMBOLSKEY TO SYMBOLS CONTENTSContents Note the following before startingDear customer INTRODUCTIONWhat is what on the clearing saw? BC WHAT IS WHAT?6 - English What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 WDecompression valve FC 2145 S, FC 2145 W What is what on the clearing saw? CC WARNING! The ignition system of this GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! Listen out for warning signals orA BA B Machine′s safety equipmentWARNING! Never use a machine with faulty Mufﬂer Cutting attachment guardVibration damping system Quick releaseWARNING! The inside of the mufﬂer contain Locking nutLocking screw WARNING! Mufﬂers ﬁtted with catalyticWARNING! Always stop the engine before Cutting equipmentWARNING! Using an incorrect cutting General rulesTrimmer head Sharpening the saw bladeAssembling the handlebar and throttle BC 2145, CC ASSEMBLYAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W Transport position, handlebarN E F P BA C L M C AAssembling the cutting equipment WARNING! When ﬁtting the cuttingH P B C Fitting the blade guard and saw bladeFitting the trimmer guard and trimmer head Trimmy SII L M C AWARNING! When using a clearing saw it Adjusting the harness and clearing sawFitting other guards and cutting attachments Standard harness2 Grass clearing Vector harnessWARNING! Take care when handling fuel Fuel safetyFUEL HANDLING FuelDo not smoke or place hot objects near fuel FuelingWARNING! Taking the following precautions will lessen the risk of ﬁre WARNING! The catalytic converter mufﬂerWARNING! The complete clutch cover and STARTING AND STOPPINGCheck before starting Starting and stoppingHeated handles FC 2145 W WARNING! When the engine is started withStarting StoppingWARNING! Neither the operator of the WORKING TECHNIQUESGeneral working instructions WARNING! Machines ﬁtted with saw blades Working methodsWARNING! Watch out for thrown objects WARNING! Sometimes branches or grassBrush cutting with a saw blade Grass clearing using a grass bladeSweeping TrimmingClearing CuttingWARNING! If the idle speed cannot be MAINTENANCECarburetor FC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Setting procedure without a load Blade can be usedSetting procedure with a load Trimmer head should be used Proceed as follows MufﬂerCooling system Air ﬁlterCleaning the air ﬁlter Bevel gearDrive shaft Spark plugTemperature 5C 41F or colder Winter useDaily Maintenance scheduleMaintenance maintenanceFC 2145 S TECHNICAL DATATechnical data WeightIgnition system FC 2145, FC 2145 S, FC 2145 W Approved accessoriesType Cutting attachment guard, Art. noYOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENT20mm Poly Trim6 Nm ~ 3,5 m Trimmy SII095-.130 7,0 mPage 2,7-3,3 mm Auto1,1 Kw 1,1 Kw2,7-3,3 mm Tap n’Go 45 Spin10 m 10 cm 4,3 m´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨