Jonsered CC 2145 Assembly, Assembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W

Page 14
ASSEMBLY

ASSEMBLY

Assembling the handlebar and throttle (BC 2145, CC 2145)

Remove the screw at the rear of the throttle handle.

Slide the throttle handle onto the right side of the handlebar, (see diagram).

Align the screw hole in the throttle handle with the hole in the handlebar.

Refit the screw in the hole in the rear of the throttle handle.

Screw the screw through the handle and handlebar. Tighten it.

Unscrew the knob from the handlebar mounting.

Position the handlebar as shown. Fit the mounting components and tighten the knob lightly.

Put on the harness and hang the machine from the support hook. Now make a final adjustment so that the machine is in a comfortable working position when it hangs from the harness.

Tighten the knob.

Assembling the handlebar and throttle (FC 2145, FC 2145 S, FC 2145 W)

Unscrew the knob from the handlebar mounting.

Position the handlebar as shown. Fit the mounting components and tighten the knob lightly.

Fit the right handle to the handlebar using the screw, washer, sleeve and nut as shown. Tighten.

Put on the harness and hang the machine from the support hook. Now make a final adjustment so that the machine is in a comfortable working position when it hangs from the harness.

Transport position, handlebar

The handlebar can easily be turned to fit along the shaft for easier transportation and storage.

Loosen the knob.Turn the handlebar clockwise so that the throttle handle rests against the engine.

Now twist the handlebar around the shaft. Tighten the knob.

Fit the transport guard to the cutting attachment.

14 – English

Image 14
Contents Operator’s manual EPA KEY TO SYMBOLS SymbolsNote the following before starting CONTENTSContents KEY TO SYMBOLSINTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw? BC6 - English What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 WDecompression valve FC 2145 S, FC 2145 W What is what on the clearing saw? CC WARNING! Listen out for warning signals or GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! The ignition system of thisA BA B Machine′s safety equipmentWARNING! Never use a machine with faulty Quick release Cutting attachment guardVibration damping system MufflerWARNING! Mufflers fitted with catalytic Locking nutLocking screw WARNING! The inside of the muffler containGeneral rules Cutting equipmentWARNING! Using an incorrect cutting WARNING! Always stop the engine beforeSharpening the saw blade Trimmer headTransport position, handlebar ASSEMBLYAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W Assembling the handlebar and throttle BC 2145, CCWARNING! When fitting the cutting L M C AAssembling the cutting equipment N E F P BA CL M C A Fitting the blade guard and saw bladeFitting the trimmer guard and trimmer head Trimmy SII H P B CStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments WARNING! When using a clearing saw itVector harness 2 Grass clearingFuel Fuel safetyFUEL HANDLING WARNING! Take care when handling fuelWARNING! The catalytic converter muffler FuelingWARNING! Taking the following precautions will lessen the risk of fire Do not smoke or place hot objects near fuelStarting and stopping STARTING AND STOPPINGCheck before starting WARNING! The complete clutch cover andStopping WARNING! When the engine is started withStarting Heated handles FC 2145 WWARNING! Neither the operator of the WORKING TECHNIQUESGeneral working instructions WARNING! Sometimes branches or grass Working methodsWARNING! Watch out for thrown objects WARNING! Machines fitted with saw bladesGrass clearing using a grass blade Brush cutting with a saw bladeCutting TrimmingClearing SweepingWARNING! If the idle speed cannot be MAINTENANCECarburetor FC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Setting procedure without a load Blade can be usedSetting procedure with a load Trimmer head should be used Air filter MufflerCooling system Proceed as followsSpark plug Bevel gearDrive shaft Cleaning the air filterWinter use Temperature 5C 41F or coldermaintenance Maintenance scheduleMaintenance DailyWeight TECHNICAL DATATechnical data FC 2145 SEngine Cutting attachment guard, Art. no Approved accessoriesType FC 2145, FC 2145 S, FC 2145 WFEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS20mm Poly Trim6 Nm 7,0 m Trimmy SII095-.130 ~ 3,5 mPage 1,1 Kw Auto1,1 Kw 2,7-3,3 mm10 cm 4,3 m Tap n’Go 45 Spin10 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨