Jonsered CC 2145 manual Fitting other guards and cutting attachments, Standard harness, Assembly

Page 17

Fitting other guards and cutting attachments

ASSEMBLY

Fitting other guards and cutting attachments

•Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

L

M C

A

•Fit the drive disc (B) on the output shaft.

H

P

B

C

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

•To dismantle, follow the instructions in the reverse order.

Adjusting the harness and clearing saw

WARNING! When using a clearing saw it

!must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release.

Standard harness

Safety release

At the front is an easily accessible, quick release. Use this if the engine catches ﬁre or in any other emergency situation that requires you to free yourself from the machine and harness.

Spreading the load on your shoulders

A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders.

Correct height

1Forestry clearing

The machine should be supported in a harness when forestry clearing so that the cutting equipment is angled slightly forwards in relation to the ground. Adjust the height using the strap on the harness for the support hook.

English – 17

Image 17

Contents Operator’s manual EPA Symbols KEY TO SYMBOLSContents CONTENTSNote the following before starting KEY TO SYMBOLSDear customer INTRODUCTIONWhat is what on the clearing saw? BC WHAT IS WHAT?6 - English What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 WDecompression valve FC 2145 S, FC 2145 W What is what on the clearing saw? CC Personal protective equipment GENERAL SAFETY PRECAUTIONSWARNING! Listen out for warning signals or WARNING! The ignition system of thisA BA B Machine′s safety equipmentWARNING! Never use a machine with faulty Vibration damping system Cutting attachment guardQuick release MufﬂerLocking screw Locking nutWARNING! Mufﬂers ﬁtted with catalytic WARNING! The inside of the mufﬂer containWARNING! Using an incorrect cutting Cutting equipmentGeneral rules WARNING! Always stop the engine beforeTrimmer head Sharpening the saw bladeAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W ASSEMBLYTransport position, handlebar Assembling the handlebar and throttle BC 2145, CCAssembling the cutting equipment L M C AWARNING! When ﬁtting the cutting N E F P BA CFitting the trimmer guard and trimmer head Trimmy SII Fitting the blade guard and saw bladeL M C A H P B CFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness WARNING! When using a clearing saw it2 Grass clearing Vector harnessFUEL HANDLING Fuel safetyFuel WARNING! Take care when handling fuelWARNING! Taking the following precautions will lessen the risk of ﬁre FuelingWARNING! The catalytic converter mufﬂer Do not smoke or place hot objects near fuelCheck before starting STARTING AND STOPPINGStarting and stopping WARNING! The complete clutch cover andStarting WARNING! When the engine is started withStopping Heated handles FC 2145 WWARNING! Neither the operator of the WORKING TECHNIQUESGeneral working instructions WARNING! Watch out for thrown objects Working methodsWARNING! Sometimes branches or grass WARNING! Machines ﬁtted with saw bladesBrush cutting with a saw blade Grass clearing using a grass bladeClearing TrimmingCutting SweepingWARNING! If the idle speed cannot be MAINTENANCECarburetor FC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Setting procedure without a load Blade can be usedSetting procedure with a load Trimmer head should be used Cooling system MufﬂerAir ﬁlter Proceed as followsDrive shaft Bevel gearSpark plug Cleaning the air ﬁlterTemperature 5C 41F or colder Winter useMaintenance Maintenance schedulemaintenance DailyTechnical data TECHNICAL DATAWeight FC 2145 SWeight Type Approved accessoriesCutting attachment guard, Art. no FC 2145, FC 2145 S, FC 2145 WYOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENT20mm Poly Trim6 Nm 095-.130 Trimmy SII7,0 m ~ 3,5 mPage 1,1 Kw Auto1,1 Kw 2,7-3,3 mm10 m Tap n’Go 45 Spin10 cm 4,3 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨