Jonsered CC 2145 manual Maintenance schedule, Daily, Weekly, Monthly, maintenance

Page 32
Maintenance schedule

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop.

Maintenance

Daily

Weekly

Monthly

maintenance

maintenance

maintenance

 

 

 

 

 

Clean the outside of the machine.

X

 

 

 

 

 

 

Check that the harness is not damaged.

X

 

 

 

 

 

 

Make sure the throttle trigger lock and the throttle function correctly from a

X

 

 

safety point of view.

 

 

 

 

 

 

 

 

 

Check that the handle and handlebar are undamaged and secured

X

 

 

correctly.

 

 

 

 

 

 

 

 

 

Check that the stop switch works correctly.

X

 

 

 

 

 

 

Check that the cutting attachment does not rotate at idle.

X

 

 

 

 

 

 

Clean the air filter. Replace if necessary.

X

 

 

 

 

 

 

Check that the guard is undamaged and not cracked. Replace the guard if

X

 

 

it has been exposed to impact or is cracked.

 

 

 

 

 

 

 

 

 

Check that the blade is correctly centred, is sharp, and is not cracked. An

 

 

 

off-centre blade will cause vibration that could result in damage to the

X

 

 

machine.

 

 

 

 

 

 

 

Check that the trimmer head is undamaged and not cracked. Replace the

X

 

 

trimmer head if necessary.

 

 

 

 

 

 

 

 

 

Check that the locking nut of the cutting equipment is tighten correctly.

X

 

 

 

 

 

 

Check that the locking screw is tightened when using a support cup with

X

 

 

bearings.

 

 

 

 

 

 

 

 

 

Check that the transport guard for the blade is intact and that it can be

X

 

 

secured correctly.

 

 

 

 

 

 

 

 

 

Check that nuts and screws are tight.

X

 

 

 

 

 

 

Check that there are no fuel leaks from the engine, tank or fuel lines.

X

 

 

 

 

 

 

Check the starter and starter cord.

 

X

 

 

 

 

 

Check that the vibration damping elements are not damaged.

 

X

 

 

 

 

 

Clean the outside of the spark plug. Remove it and check the electrode

 

 

 

gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that

 

X

 

the spark plug is fitted with a suppressor.

 

 

 

 

 

 

 

Clean the machine’s cooling system.

 

X

 

 

 

 

 

Clean or replace the spark arrestor screen on the muffler (only applies to

 

X

 

mufflers without a catalytic converter).

 

 

 

 

 

 

 

 

 

Clean the outside of the carburettor and the space around it.

 

X

 

 

 

 

 

Check that the bevel gear is filled three-quarters full with lubricant. Fill if

 

X

 

necessary using special grease.

 

 

 

 

 

 

 

 

 

Check that the safety release on the harness is not damaged and works.

 

 

X

 

 

 

 

Check the fuel filter from contamination and the fuel hose from cracks or

 

 

X

other defects. Replace if necessary.

 

 

 

 

 

 

 

 

 

Check all cables and connections.

 

 

X

 

 

 

 

Check the clutch, clutch springs and the clutch drum for wear. Replace if

 

 

X

necessary by an autorized service workshop.

 

 

 

 

 

 

 

 

 

Replace the spark plug. Check that the spark plug is fitted with a

 

 

X

suppressor.

 

 

 

 

 

 

 

 

 

Check and clean the spark arrestor screen on the muffler (only applies to

 

 

X

mufflers fitted with a catalytic converter).

 

 

 

 

 

 

 

 

 

Lubricate the drive shaft with the special grease.

Do this every three months.

 

 

 

 

 

Replace the vibration damping elements after each season, however, at

 

 

 

least once a year.

 

 

 

 

 

 

 

32 – English

Image 32
Contents Operator’s manual EPA KEY TO SYMBOLS SymbolsCONTENTS ContentsNote the following before starting KEY TO SYMBOLSINTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw? BC6 - English What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 WDecompression valve FC 2145 S, FC 2145 W What is what on the clearing saw? CC GENERAL SAFETY PRECAUTIONS Personal protective equipmentWARNING! Listen out for warning signals or WARNING! The ignition system of thisA BA B Machine′s safety equipmentWARNING! Never use a machine with faulty Cutting attachment guard Vibration damping systemQuick release MufflerLocking nut Locking screwWARNING! Mufflers fitted with catalytic WARNING! The inside of the muffler containCutting equipment WARNING! Using an incorrect cuttingGeneral rules WARNING! Always stop the engine beforeSharpening the saw blade Trimmer headASSEMBLY Assembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 WTransport position, handlebar Assembling the handlebar and throttle BC 2145, CCL M C A Assembling the cutting equipmentWARNING! When fitting the cutting N E F P BA CFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SIIL M C A H P B CAdjusting the harness and clearing saw Fitting other guards and cutting attachmentsStandard harness WARNING! When using a clearing saw itVector harness 2 Grass clearingFuel safety FUEL HANDLINGFuel WARNING! Take care when handling fuelFueling WARNING! Taking the following precautions will lessen the risk of fireWARNING! The catalytic converter muffler Do not smoke or place hot objects near fuelSTARTING AND STOPPING Check before startingStarting and stopping WARNING! The complete clutch cover andWARNING! When the engine is started with StartingStopping Heated handles FC 2145 WWARNING! Neither the operator of the WORKING TECHNIQUESGeneral working instructions Working methods WARNING! Watch out for thrown objectsWARNING! Sometimes branches or grass WARNING! Machines fitted with saw bladesGrass clearing using a grass blade Brush cutting with a saw bladeTrimming ClearingCutting SweepingWARNING! If the idle speed cannot be MAINTENANCECarburetor FC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Setting procedure without a load Blade can be usedSetting procedure with a load Trimmer head should be used Muffler Cooling systemAir filter Proceed as followsBevel gear Drive shaftSpark plug Cleaning the air filterWinter use Temperature 5C 41F or colderMaintenance schedule Maintenancemaintenance DailyTECHNICAL DATA Technical dataWeight FC 2145 STECHNICAL DATA Approved accessories TypeCutting attachment guard, Art. no FC 2145, FC 2145 S, FC 2145 WFEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS20mm Poly Trim6 Nm Trimmy SII 095-.1307,0 m ~ 3,5 mPage Auto 1,1 Kw1,1 Kw 2,7-3,3 mmTap n’Go 45 Spin 10 m10 cm 4,3 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨