Jonsered CC 2145 manual L M C A, Assembling the cutting equipment, Assembly, N E F P Ba C

Page 15
Assembling the cutting equipment

ASSEMBLY

Assembling the cutting equipment

WARNING! When fitting the cutting

!

attachment it is extremely important that the

raised section on the drive disc/support

•Position the blade (D) with the drive disk (B). Make sure that the blade is centered by fitting it to the guide on the drive disk.

•Fit the support flange (F) on the output shaft so that it rests against the blade.

flange engages correctly in the centre hole
of the cutting attachment. If the cutting
attachment is fitted incorrectly it can result
in serious and/or fatal personal injury.

D

N

WARNING! When fitting the cuttingraised section on the drive disc/supportE

Fflange engages correctly in the centre holeof the cutting attachment. If the cutting

Pattachment is fitted incorrectly it can resultin serious and/or fatal personal injury.

BNLWARNING! Tighten the lock screw (N) in theManual backgroundA CManual backgroundManual background

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

Fitting the blade guard/combination guard, grass blade and ball-bearing- mounted support cup

•Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

L

MManual backgroundManual background C

A

CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

•Fit the drive disc (B) on the angle gear’s output shaft.

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the output shaft until one of the holes in the drive disk aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

ML

•Screw the support cup (E) onto the output shaft threads (CAUTION! Left-hand thread). Tighten to a torque of 35- 50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool kit. Note that the locking pin (C) must remain inside the gear housing to lock the drive disk. Hold the shaft of the socket spanner as close to the blade guard/combination guard as possible.

WARNING! Tighten the lock screw (N) in the

!center hole of the support cup. Tighten to a torque of 35-50 Nm (3.5-5.0 kpm), CAUTION! Left-hand thread. If the lock screw is not fitted in the support cup, there is a risk that the support cup will come unscrewed. This means that the blade will also come loose, which could result in serious or fatal injury to the operator or others.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operator’s manual EPA Symbols KEY TO SYMBOLSKEY TO SYMBOLS CONTENTSContents Note the following before startingDear customer INTRODUCTIONWhat is what on the clearing saw? BC WHAT IS WHAT?What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 W Decompression valve FC 2145 S, FC 2145 W6 - English What is what on the clearing saw? CC WARNING! The ignition system of this GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! Listen out for warning signals orMachine′s safety equipment WARNING! Never use a machine with faultyA BA B Muffler Cutting attachment guardVibration damping system Quick releaseWARNING! The inside of the muffler contain Locking nutLocking screw WARNING! Mufflers fitted with catalyticWARNING! Always stop the engine before Cutting equipmentWARNING! Using an incorrect cutting General rulesTrimmer head Sharpening the saw bladeAssembling the handlebar and throttle BC 2145, CC ASSEMBLYAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 W Transport position, handlebarN E F P BA C L M C AAssembling the cutting equipment WARNING! When fitting the cuttingH P B C Fitting the blade guard and saw bladeFitting the trimmer guard and trimmer head Trimmy SII L M C AWARNING! When using a clearing saw it Adjusting the harness and clearing sawFitting other guards and cutting attachments Standard harness2 Grass clearing Vector harnessWARNING! Take care when handling fuel Fuel safetyFUEL HANDLING FuelDo not smoke or place hot objects near fuel FuelingWARNING! Taking the following precautions will lessen the risk of fire WARNING! The catalytic converter mufflerWARNING! The complete clutch cover and STARTING AND STOPPINGCheck before starting Starting and stoppingHeated handles FC 2145 W WARNING! When the engine is started withStarting StoppingWORKING TECHNIQUES General working instructionsWARNING! Neither the operator of the WARNING! Machines fitted with saw blades Working methodsWARNING! Watch out for thrown objects WARNING! Sometimes branches or grassBrush cutting with a saw blade Grass clearing using a grass bladeSweeping TrimmingClearing CuttingMAINTENANCE CarburetorWARNING! If the idle speed cannot be Setting procedure without a load Blade can be used Setting procedure with a load Trimmer head should be usedFC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Proceed as follows MufflerCooling system Air filterCleaning the air filter Bevel gearDrive shaft Spark plugTemperature 5C 41F or colder Winter useDaily Maintenance scheduleMaintenance maintenanceFC 2145 S TECHNICAL DATATechnical data WeightIgnition system FC 2145, FC 2145 S, FC 2145 W Approved accessoriesType Cutting attachment guard, Art. noYOUR WARRANTY RIGHTS AND OBLIGATIONS FEDERAL EMISSION CONTROL WARRANTY STATEMENTPoly Trim 6 Nm20mm ~ 3,5 m Trimmy SII095-.130 7,0 mPage 2,7-3,3 mm Auto1,1 Kw 1,1 Kw2,7-3,3 mm Tap n’Go 45 Spin10 m 10 cm 4,3 m´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨
Top Page Image Contents