Jonsered CC 2145 manual Introduction, Dear customer

Page 4

INTRODUCTION

Dear customer!

Congratulations on your choice to buy a Jonsered product!

Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the operator′s manual, so they will also know how to properly maintain and use it.

Good luck on using your Jonsered machine!

Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.

4 – English

Image 4

Contents Operator’s manual EPA KEY TO SYMBOLS SymbolsCONTENTS ContentsNote the following before starting KEY TO SYMBOLSINTRODUCTION Dear customerWHAT IS WHAT? What is what on the clearing saw? BCDecompression valve FC 2145 S, FC 2145 W What is what on the clearing saw? FC 2145, FC 2145 S, FC 2145 W6 - English What is what on the clearing saw? CC GENERAL SAFETY PRECAUTIONS Personal protective equipmentWARNING! Listen out for warning signals or WARNING! The ignition system of thisWARNING! Never use a machine with faulty Machine′s safety equipmentA BA B Cutting attachment guard Vibration damping systemQuick release MufﬂerLocking nut Locking screwWARNING! Mufﬂers ﬁtted with catalytic WARNING! The inside of the mufﬂer containCutting equipment WARNING! Using an incorrect cuttingGeneral rules WARNING! Always stop the engine beforeSharpening the saw blade Trimmer headASSEMBLY Assembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 WTransport position, handlebar Assembling the handlebar and throttle BC 2145, CCL M C A Assembling the cutting equipmentWARNING! When ﬁtting the cutting N E F P BA CFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SIIL M C A H P B CAdjusting the harness and clearing saw Fitting other guards and cutting attachmentsStandard harness WARNING! When using a clearing saw itVector harness 2 Grass clearingFuel safety FUEL HANDLINGFuel WARNING! Take care when handling fuelFueling WARNING! Taking the following precautions will lessen the risk of ﬁreWARNING! The catalytic converter mufﬂer Do not smoke or place hot objects near fuelSTARTING AND STOPPING Check before startingStarting and stopping WARNING! The complete clutch cover andWARNING! When the engine is started with StartingStopping Heated handles FC 2145 WGeneral working instructions WORKING TECHNIQUESWARNING! Neither the operator of the Working methods WARNING! Watch out for thrown objectsWARNING! Sometimes branches or grass WARNING! Machines ﬁtted with saw bladesGrass clearing using a grass blade Brush cutting with a saw bladeTrimming ClearingCutting SweepingCarburetor MAINTENANCEWARNING! If the idle speed cannot be Setting procedure with a load Trimmer head should be used Setting procedure without a load Blade can be usedFC 2145, FC 2145 S, FC 2145 W Speed control at 13500 rpm Mufﬂer Cooling systemAir ﬁlter Proceed as followsBevel gear Drive shaftSpark plug Cleaning the air ﬁlterWinter use Temperature 5C 41F or colderMaintenance schedule Maintenancemaintenance DailyTECHNICAL DATA Technical dataWeight FC 2145 STECHNICAL DATA Approved accessories TypeCutting attachment guard, Art. no FC 2145, FC 2145 S, FC 2145 WFEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS6 Nm Poly Trim20mm Trimmy SII 095-.1307,0 m ~ 3,5 mPage Auto 1,1 Kw1,1 Kw 2,7-3,3 mmTap n’Go 45 Spin 10 m10 cm 4,3 m 2,7-3,3 mm´z+Rvy¶5s¨ ´z+Rvy¶5s¨ Page 1150868-95 ´z+Rvy¶5s¨ ´z+Rvy¶5s¨